Gorenje KGV 200-1 Скачать руководство пользователя страница 6

33

OPERATION AND MAINTENANCE

The water heater is ready for use once it has been connected to water and other sources of 

heating.

The usual main sources of heating of water for sanitary use are central heating or solar 

power; in this case any regulation of water heating is performed in the heating system.

Electric heater type R may be additionally installed on the flange 

180mm, or electric heater type 

SH to the connecting bushing G 6/4, which are used for additional heating of water:

-  If you need higher temperature of water than assured by other heating sources,

-  If due to seasonal or other conditions there are no main heating sources.

In case of exposure to sub-zero temperatures, the water should be thoroughly drained from 

the heater before the onset of freezing conditions.

Once that is done, open the hot water tap on one of the mixer taps connected to the water 

heater. The water from the water heater drains by way of the drain valve on the inlet pipe. 

External parts of the water heater may be cleaned with a mild detergent solution. Do not use 

solvents and abrasive cleaners.

Regular preventive maintenance inspections ensure faultless performance and long life of 

your heater. The first of these inspections should be carried out by an authorised maintenance

service provider about two years from the date of installation in order to inspect the wear 

of  the  corrosion  protection  anode  and  to  remove  any  limestone  as  required.  Build-up  of 

limestone is a product of quality, quantity and temperature of water flowing through the water

heater. While inspecting the heater, the maintenance service provider will also recommend 

the date of the next inspection.

Wear of the corrosion protection anode is carried out visually. Replacement is required when 

the inspection reveals that the anode diameter has been substantially reduced or worn all 

the way to the steel core.

Tank warranty is subject to regular inspections of the protective anode. 

In the event of the water heater breaking down, you are kindly requested to contact 

the authorised maintenance service provider located closest to you. Please do not 

attempt to repair the unit yourself.

GB

Содержание KGV 200-1








Отзывы: