- 10 -
Preset memory
This unit is able to store 24 FM and 16 MW radio stations in the preset memory.
1.
In TUNER mode, select FM or MW waveband.
2.
Tune to a radio station either manually or by automatic search.
3.
Press the PROG / CLK ADJ (6, 38) button, “PROGRAM” indicates in the
Display, and “- -“will flash, to indicate that a radio station can be preset.
4.
Press the PRESET – (14, 47) or (15, 32) button repeatedly until
the desired memory position number appears in the Display.
5.
Press the PROG / CLK ADJ (6, 38) button again save programmed station.
6.
In order to store the remaining stations, repeat steps 2 - 5 accordingly.
ST/MO button (17, 33)
Press this button repeatedly to switch between stereo and mono reception.
²
When the unit is tuned into a stereo broadcast with a good signal, "ST" will show in the display.
²
If a stereo broadcast is received, but with interference, it is recommended to switch to mono mode
.
Selecting the tuner preset station memories
Press the PRESET – (14, 47) or (15, 32) buttons to select preset stations that are stored in
the memory.
Note:
To access preset stations1-9, you must press “0” first.
Reception tips
FM:
Extend FM Wire Antenna (23) completely for best reception. If a stereo
broadcast received, “ST” will indicate in the Display.
MW: This unit is equipped with a built-in directional ferrite antenna, move and
rotate the unit for best reception.
IMPORTANT NOTES ON PLAYING CDS
Notes when operating the CD player
²
The disc loader may only be opened or closed by pressing the OPEN/CLOSE (10, 39) button.
²
To remove the disc, hold it by the edges and remove from the holder.
Loading discs
1. Press the
STANDBY (5, 30) button to turn “ON” the unit.
2. Press the CD/USB/SD (9, 46) button repeatedly until “CD” indicates in the
Display to select CD mode.
3. Press the OPEN CLOSE (10, 39) button to open CD tray (21).
4. Place the CD into the tray with the label side uppermost.
5. Press the OPEN/CLOSE (10, 39) button again to close CD tray (21). The CD
player will automatically scan the disc. The total number of tracks and the
playback time will show in the display. If the scanned disc is a MP3 or WMA
disc, the total number of tracks and total folder number show in the display.
If there is no disc in the unit, the display will show “
DISC”
Notes on MP3, WMA, CD-R / RW discs
²
Because of non-standardized format definition / production of MP3, WMA and CD-R/RW discs,
playback quality & performance are not guaranteed.
²
Playback of MP3, WMA, CD-R / CD-RW discs may depend on recording conditions.
²
Do not attach labels to either surface of the disc. This may cause the unit to malfunction.
²
Do not use scratched or dirty discs as this may cause the unit to malfunction.
Track No. Playback time
Folder No. Total track No.
- 11 -
COMPACT DISC OPERATION
Normal Playback
After loading a CD, press the
PLAY/PAUSE (14, 47) button to start playback.
The track number and playing time are indicated in the display.
Pause control
To pause temporarily during CD playback press the
PLAY/PAUSE (14, 47)
button. The disc playback will pause and the elapsed track time will flash in the
display. Press the
PLAY/PAUSE (14, 47) button again to resume playback.
Skip track and high-speed music search
During playback, press the
/ TUNING or
/ TUNING (20, 35) buttons to skip
to the next or previous tracks.
During playback, press and hold the
/ TUNING or
/ TUNING (20, 35) buttons
to search forwards or backwards through the current track.
When the desired part of the track is located, release the button and playback will resume.
Using numerical buttons
You can use the Numerical 0-9 (49) buttons to directly select a track to play. Note that to select tracks
between 1-9, the 0 button must be pressed first, for example:
Track no. 2
- Press “0” first, then press “2”.
Track no. 12
- Press “1” first, then press “2”.
PLAY MODE CONTROL
1.
Repeat the entire track
Select the track to be repeated and begin playback. Press the PLAY MODE
(17, 33) button once. The
RPT
indicator will show in the display and the
selected track will be repeated continuously.
2.
Repeat all
Press the PLAY MODE
(17, 33) button twice. The
RPT
indicator will show in
the display and all the tracks on the disc will be repeated continuously.
3.
Random playback
The Random playback feature allows you play all the tracks on the current
disc in a random order. This function can be selected when the disc is
playing or when in stop mode. Press the PLAY MODE
(17, 33)
button third
times to random playback mode. The
RDM
indicator is shown in the display.
If necessary, press the
PLAY/PAUSE (14, 47) button to begin playback. The player will
randomly select a track to play from the disc.
4.
Intro playback
Press PLAY MODE
(17, 33)
button four times to play a brief intro of each
track for 10 seconds and the
INTRO
indicator is shown in the display.
To cancel
INTRO
mode, press the PLAY MODE (17, 33) button again and normal
playback will resume.
Programmed Playback
It is possible to program a selection of up to 32 tracks for playback. Individual
tracks can be programmed more than once.
1.
After loading a disc, Press the PROG / CLK ADJ (6, 38)
button in stop mode.
PROGRAM
and
- - PR01
will show in the display.
2.
Press the
/ TUNING
or
/ TUNING
(20, 35)
buttons repeatedly to select the desired track number.
3.
Press PROG / CLK ADJ (6, 38) button to confirm the first programmed track.
- - PR02
now shows in the display and waiting for next programming.
4.
Repeat steps 2 and 3 to store further tracks.
5.
When programming is complete, press the
PLAY/PAUSE (14, 47)
button to begin playback of the selected tracks.
