Goodman AC9S80 Скачать руководство пользователя страница 7

Страница: 7 / 55

SYSTEM OPERATION

Twinning

Two furnaces of the same model may be twinned. The in-

tegrated control board has a 3/16” terminal labeled “TWIN”

located beside the low voltage thermostat connection strip.

Twinning allows simultaneous operation of two furnaces and

forces the indoor blower motors of each furnace to operate

synchronously into a common duct system. Using the twin-

ning function will require only field installed wiring with no

external kits or parts. The staging and speed tap options

must be set the same on both furnaces.

NOTE:

Each furnace must be connected to it’s own 115

VAC power supply. The L1 connection to each furnace must

be in phase (connected to circuit breakers on the same 115

VAC service panel phase leg). To verify that the furnaces

are in phase, check from L1 to L1 on each furnace with a

voltmeter. If the furnaces are in phase, the voltage between

both furnaces will be ZERO.

ROOM THERMOSTAT

Y/Y1

TWIN

COND UNIT

CONTACTOR

COND UNIT

CONTACTOR

FURNACE 1

FURNACE 2

115 Volt Line Connection of Accessories

(Humidifier and Electronic Air Cleaner)

The furnace integrated control module is equipped with line

voltage accessory terminals for controlling power to an op-

tional field-supplied humidifier and/or electronic air cleaner.

The accessory load specifications are noted in the chart:

Humidifier

1.0 Amp maximum at 120 VAC

Electronic Air Cleaner

1.0 Amp maximum at 120 VAC

Turn OFF power to the furnace before installing any acces-

sories. Follow the humidifier or air cleaner manufacturers’ in

structions for locating, mounting, grounding, and controlling

these accessories. Accessory wiring connections are to be

made through the 1/4” quick connect terminals provided on

the furnace integrated control module. The humidifier and

electronic air cleaner hot terminals are identified as HUM H

and EAC H. The humidifier and electronic air cleaner neutral

terminals are identified as NEUTRAL. All field wiring must

conform to applicable codes. Connections should be made

as shown.

If it is necessary for the installer to supply additional line

voltage wiring to the inside of the furnace, the wiring must

conform to all local codes, and have a minimum temperature

rating of 105°C. All line voltage wire splices must be made

inside the furnace junction box.

The integrated control module humidifier terminal (HUM

H) is energized with 115 volts whenever the induced draft

blower is energized. The integrated control module electron-

ic air cleaner terminal (EAC H) is energized with 115 volts

whenever the circulator blower is energized. This terminal

can also be used to provide 115 volt power to a humidifier

transformer. The remaining primary transformer wire would

be connected to the Line N on the control board.

WARNING

HIGH VOLTAGE!

To avoid personal injury or death due to electri

cal shock, disconnect electrical power before

servicing or changing any electrical wiring.

115 VAC EAC

115 VAC HUM

W R G C Y

Accessories - Accessories Wiring

Low Voltage Humidifier

The furnace integrated control module is equipped with

a low voltage terminal for providing power to an optional

field-supplied 24 volt humidifier. The 24V HUM terminal is

energized any time the draft inducer is powered. See con-

nection diagram below.

NOTE:

This is a 24 volt circuit only, the common connec-

tion must be on C terminal of the low voltage terminal strip

(where thermostat wires are connected). Wiring for this cir-

cuit must NOT be connected to the line N location where line

voltage neutral wires are connected.

Содержание AC9S80
























































Результаты поиска

Содержание AC9S80

Отзывы:

Бренды по названию

Популярные бренды

Goodman AC9S80, Обслуживание и устранение неисправностей

Результаты поиска

Содержание AC9S80

Отзывы:

Бренды по названию

Популярные бренды