- 2 -
1
2
4
Plug-in Installation
Find a suitable location to mount the fixture that will reach the power supply.
Remove the diffuser by pulling back and up on the top
edge of the diffuser (
Fig. 1
).
This fixture can be mounted using the keyholes on the
top or the back side of the fixture. Once the mounting
orientation is determined, place the fixture up to the
mounting surface and mark the narrow end of the
keyhole slots (
Fig. 4
).
Slide the fixture over until the narrow ends of the
keyhole slots are under the heads of the wood screws
(
Fig. 6
). Finish tightening the wood screws until they are
firmly seated and the fixture is tightly secured to the
mounting surface.
Place the diffuser in the top lip. Push the grooved edge
of the diffuser down into the bottom edge until it locks in
(
Fig. 7
). Once the fixture is installed, plug in power cord
to the closest outlet.
6
5
3
Remove the bulb from the fixture by placing both
thumbs on the metal ends of the bulb. While applying
slight pressure on the metal ends, roll the bulb
forward until the contact pins on the ends of the bulb
disengage from the socket (
Fig. 2
). Pull the bulb
straight out from the socket and set aside (
Fig. 3
).
Re-install the bulb into the sockets by aligning the contact pins of the bulb with
the slots in the sockets. Press the metal ends of the bulb into the sockets and roll
the bulb backwards until the contact pins engage into the sockets.
Use an awl or nail to dimple the screw holes or drill a
1/16 in. pilot hole at the marked locations. Tighten the
screws leaving 1/2 in. of the screw protruding from the
surface (
Fig.5
).
7
8
Important Safety Instructions
Fig. 6
Fig. 5
Fig. 4
Fig. 2
Fig. 3
Fig. 1
5. Handle bulb with care during replacing. The glass tube of the bulb is
very fragile and can break easily.
6. Not intended for illumination of aquariums.
7. Not intended for recessed installation in ceilings or soffits.
8. Do NOT mount over sinks or stoves.
9. Do NOT mount the fixture to cabinets having a material thickness less
than 1/4 in.
10. Do NOT install the fixture inside of enclosed cabinets.
11. Electrical requirements:120VAC, 60Hz, 15W.
12. Do NOT attempt to install while plugged in.
13. Do NOT use an extension cord. Use a power strip with integral
over current protection to supply power to the fixture.
14. Use only insulated staples or plastic ties (not included) to secure the cords.
15. Do not run ANY cords behind walls, ceilings, soffits, cabinets or a similar
permanent structure where it may be inaccessible for examination.
IMPORTANT:
The fluorescent bulb may be packed in a separate area of the
packing materials or may already be placed into their respective sockets.
Do NOT operate the fixture with the protective support collar in place. Cut
the collar off or remove the bulb from the sockets and slide the support
collar off the lamp.
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE FIXTURE TO
REFER TO THEM AT A LATER TIME.
Fig. 7
Bulb Replacement Instructions
Fig. 1
Remove the diffuser by pulling back and up on the top
edge of the diffuser (
Fig. 1
).
1
2
Replace only with a linear fluorescent bulb: Bulb #F15T8 15 W. Do not replace with any
other bulb wattage. Turn fixture off/unplug and allow to cool before replacing bulb.
Remove the bulb from the fixture by placing both
thumbs on the metal ends of the bulb (
Fig. 2
). While
applying slight pressure on the metal ends, roll the bulb
forward until the contact pins on the ends of the bulb
disengage from the socket (
Fig. 3
). Pull the bulb straight
out from the socket and set aside.
Fig. 2
Fig. 3
