The Golight® RadioRay® Model 2000/2051 & 20004/20514
are designed to be permanently attached to a vehicle. The
2-Speed Searchlight with Directional Flexibility is controlled by
a wireless remote, which gives the operator a full 370°
horizontal rotation and a 135° vertical tilt with fingertip control.
The RadioRay® provides superior light penetration with Cr5
PentaBeam™ technology in a halogen configuration or with
state of the art P-Vex™ lens and LED technology.
The RadioRay® Includes:
• RadioRay® Searchlight
• Wireless Remote Control
• 2 A23 12V Batteries
• Permanent Mounting Gasket
• Rockguard (not Available with LED units)
MOUNTING INSTRUCTIONS
Determine the location for the light on your vehicle or boat.
The small arrow on the base indicates the normal forward
direction of the light. The light will rotate to the left of this
arrow approximately 185 and to the right approximately 185.
The beam will angle down about 45 and angles up to 90. The
location should take into consideration this beam movement to
ensure optimum usability.
Once the position and orientation are decided upon—use the
black rubber gasket as a footprint to mark the mounting of base
to vehicle. Drill 1/4 inch hole though mounting surface in the
middle of the footprint for passage of the power cord. Use
silicone sealant to fill opening around power cord. IMPOR-
TANT: Allow 3” of cord to remain under the light to ensure full
370 rotation.
You should choose screw or bolt fasteners appropriate to the
surface to which you intend to attach the light. If you intend
to use the four small plastic caps provided to cover the screw
heads once installed, a #8 round head is recommended.
The black gasket should be installed on the lamp base prior to
attachment to the vehicle surface. NOTE: The small drain hole
in the edge of the gasket should normally face opposite the
forward direction of the vehicle—opposite the arrow molded in
the front of the base. Silicone or other like sealants should not
be used around the base gasket as it will limit the light’s ability
to drain excess water properly.
The 12 Volt DC power wire should be joined to the leads under the
lamp with appropriate automotive wire attachments. The light is
not polarity sensitive. Power should be fused at 10 Amps and be
on a dedicated circuit, or wired to an appropriate automotive relay
system.
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight® RadioRay® is controlled with a programmable remote
with 2187 different channels. This feature allows you the freedom
to change the channel selection, and the receiver relearns the new
selection.
PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, and it is not
necessary to re-program the transmitter, unless you experience
outside interference.
1. IMPORTANT: Disconnect power by removing fuse or
disconnecting vehicle battery.
2. Remove battery cover from remote control.
3. Set the 7 dip switches to a selection of your choice. There are 3
positions on each; positive, negative and neutral. Use a small-
screwdriver and select a position for each dip switch. *Please
note that the orientation of the +/– switch positions may vary
among different models of wireless remote controls.
4. Insert both A23 12V batteries with the +/– in the same direction.
Be sure batteries have adequate charge.
5. Replace battery cover.
a. Depress the on/off button and hold it down. Red LED
will light.
b. While holding the on/off button down, reinstall the
power (replace fuse or connect vehicle battery).
c. Keep your finger on the on/off button for 5-6 seconds,
and then release. The light should now be programmed.
OPERATION OF GOLIGHT® RADIORAY®
1. Using the remote control, turn on the light by depressing the on/
off button.
2. With the 4-way arrows on the remote control, rotate your light
to the desired location. Depending upon conditions, the wireless
remote may be used up to 80 feet from the RadioRay®.
3. The speed of the light rotation can be controlled by depressing
the tortoise/hare button one time and by depressing it again
to restore the original speed.
4. The spotlight should not be turned on when the snap on lens
cover (rockguard) is attached. (Not applicapble for LED)
BATTERY INSTALLATION AND DISPOSAL
• Remove Battery Cover: remove the phillips head screw
securing the battery cover then remove the cover. With the
battery compartment now exposed, insert batteries according
to correct polarity. Remove the batteries by gripping the
positive end of each battery and lifting.
For information regarding the proper disposal/recycling of the
batteries contact Golight at 800.557.0098
Use only 12v-A23 batteries in the Golight remote control
USAGE:
» This light is intended for off-road and utility use only
» This light is intended to be mounted outside the vehicle while
in use
» This light may only be disassembled and repaired by an
authorized representative
MISUSE:
» This light is not approved for road or highway use
» This light is not approved for underwater use
» This light is not approved for inverted mounting
» This light is not approved for use inside a vehicle or enclosure
and power should be removed prior to placing the light in such
circumstance
» This light may be damaged if operated in icing conditions
» This light may only be dismantled by an authorized Golight
representative
» Any violation of the above referenced misuses will be
considered grounds for warranty refusal
