Goldstar MA-1417B Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 35

Goldstar MA-1417B Скачать руководство пользователя страница 14

D. PCB ASSEMBLY REMOVAL

1) Remove the control panel assembly from the

cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the PCB SUB

ASSEMBLY to the control panel.

3) Disconnect the flat cable from the PCB SUB

ASSEMBLY and take off the PCB SUB ASSEMBLY.

E. DOOR MAIN ASSEMBLY REMOVAL

1) Open the door.
2) Remove the choke cover cap very carefully with a

flat-blade screwdriver.

CAUTION: Be careful not to damage door seal plate

by screwdriver.

3) Lift up and push the door.

NOTE:

1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 4 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also, adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

5-4

Door seal plate

Control Panel

Key Membrane

PCB Sub Asm

Remove door

Remove choke cover cap

Spacer

«
...
12
13
14
15
16
...
»

Содержание MA-1417B




































Отзывы:

Нет отзывов