Optional Remote Controls
Goldline offers a variety of wired and wireless remote control options for the Pro Logic. Each model gives
you the ability to control your pool’s functions from a remote location, away from the Control Center.
Wired Remote Controls
Up to 3 wired remote controls can be installed. See page 19 for wiring information.
AQL-WW-P-4
The AQL-WW-P-4 display/keypad must be mounted indoors or in a weather protected area (rain should
never touch the unit). The display/keypad is designed to mount onto a standard electrical utility box (same
box as a single light switch, ideal for new construction) or can be mounted directly onto any wall surface.
When selecting a location, note that the wire to the Pro Logic main unit must be less than 500’ long. Refer
to the remote’s installation instructions as well as the steps below:
1. Remove display/keypad baseplate from the cover by lifting up on the cover at the lower end of the
keypad. See diagram below.
2. Screw the baseplate in the desired position (screws supplied by installer).
3. See “Electrical Wiring” (page 19) for instructions on running the cable from the Pro Logic main unit
to the remote display/keypad.
AQL-SS-6B-x (x=W, G or B for White, Gray or Black)
The AQL-SS-6B is a double insulated, waterproof device which is intended for installation at the water's
edge. The remote control comes with an attached 150’ cable and is typically installed at the tile-line of the
spa wall, or in the deck, within arm's reach of a pool/spa occupant. Refer to the AQL-SS-6B installation
manual for specific mounting and wiring information.
Wireless Remote Controls
Note that the Pro Logic is compatible with AQL2 wireless remote controls only. A single AQL2-BASE-
RF Base Station must be installed on the Pro Logic in order to use any of the Goldline wireless remote
controls. With the Base Station installed, there is no limit on the number of wireless remotes that can used.
The maximum distance between the wireless remotes and the base station on the Pro Logic main control
unit is 400 feet (120m) line of sight or 200 feet (60m) through walls, etc. If in doubt about the distance, test
operation before installing the remote. All wireless models require the user to run the “Teach Wireless”
routine in the Settings Menu. This information can be found in the Pro Logic Operation Manual and the
owner’s manual of each remote.
AQL2-Tx-RF-P-4
The AQL2-Tx-RF-P-4 is a portable battery operated remote control designed to be used in a weather
protected area (rain should never hit the unit). This remote comes with a wall mounted power supply for
recharging the built-in batteries.
7
24
Lowest Speed
This is the lowest speed that the variable speed pump is allowed to run at. It is used as the
lower limit in the Low Speed Settings Menu. Set lowest speed from 10% (default) to 50%.
Highest Speed
This is the highest speed that the variable speed pump is allowed to run at. It is used as the
upper limit in the High Speed Settings Menu. Also, this is the speed that the pump will run
at during the first 3 minutes of operation anytime the pump has been off for more than 30
seconds. Set highest speed from 20% to 100% (default).
Freeze Protection
Freeze protection is used to protect the pool and plumbed equipment against freeze damage.
If freeze protection is enabled and the AIR temperature sensor falls below the freeze threshold
(see below), the Pro Logic will turn on the filter pump to circulate the water. If “Pool and Spa”
is selected in the Pool/Spa sub-menu (see page 22), the valves will also alternate between the
pool and spa every 30 minutes and the filter pump will turn off while the valves are turning.
The chlorinator will not operate if freeze protection is the only reason the pump is running.
Freeze Protection Speed
This menu only appears if freeze protection is enabled and the pump is configured for 2-
speed or variable speed pump operation. This is the speed that the pump will run at during
freeze protection operation. Select high (default) or low speed operation.
Freeze Protection Temperature
Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF
- 42ºF (1ºC - 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have
freeze protection enabled.
Heater1 Config.
+ to view/change
Heater1
Disable
Heater1 Cooldown
Disabled
Heater1 Extend
Disabled
Push to access heater options
Toggle between Enabled and Disabled (default) Heater 1
Toggle between Enabled and Disabled (default) Heater 1 Cooldown
Toggle between Enabled and Disabled (default) Heater 1 Extend
Move to previous/next configuration menu
Move to next menu item or previous/next configuration menu
Move to next menu item
Move to previous/next configuration menu
if “Heater1” is enabled
if “Heater1” is enabled
Allow Low Speed
Disabled
Toggle between Enabled and Disabled (default)
Move to next menu item or previous/next configuration menu
if “Heater1” is enabled and
1-speed filter pump is not selected
Heater1
If the heater is “Enabled”, the heater relay will turn on when the water temperature is less
than the desired temperature setting and the filter pump is running. The desired temperature
is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate
“pool” and “spa” settings. Depending on the position of the pool/spa suction valve, the
proper temperature setting will be used.
Heater Cooldown
This feature ensures that the heater cools down before water circulation is stopped. When
enabled, the Pro Logic will continue to run the filter pump for 5 minutes after the heater turns
off. During this period the filter pump LED will flash and also a “Heater Cooldown, X:XX
remaining” message will scroll on the display.
Remote Keypad
to remove cover
push up here
