Golden Compass Sport GP605 CC Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

Golden Compass Sport GP605 CC Скачать руководство пользователя страница 13

13

ASSEMBLY / DISASSEMBLY

Your

Compass Sport

™ will not power up or operate without completing

the following steps.

1. Remove front and rear battery covers. Refer to “Accessing the Batteries” on page 15.
2. Make sure both battery harnesses are plugged into the power chair and locked. See

figure 7 on page 15, and figure 10 on page 16.
3. Make sure the power harness is plugged into the power module and locked. See
figure 1 on page 14.
4. Replace the front and rear battery covers.

SEAT INSTALLATION/REMOVAL

Make sure the joystick cable does not interfere with the seat during installation.

The standard (18 x 18) seat assembly weighs about 46 pounds. Please

ask for help if you do not feel capable of safely lifting that much weight. Removal
of arms will significantly reduce the weight of seat.

Be sure the seat is correctly installed and locked before operating

your power chair

.

Never pull on the arms or use them as a handle to move the power

chair as they could inadvertently pull out of the receiver bar causing injury.

INSTALLATION

1. To install the seat, align the seat post stinger on the bottom of the seat with the hole

in the seat post on the chair. See figures 2 and 3 on page 14.
2. Push down on the seat and rotate the seat until it aligns and locks in place. See
figure 3 on page 14.
3. Attach the arms by loosening the arm width adjustment knobs. See figure 18 on page

20. Insert the arms into the receiving tube on the seat, adjust the arms to your desired
width, and tighten the arm width adjustment knobs to secure the arms in place.
4. Attach the joystick. See “Joystick Installation/Removal” on page 14.
5. Connect the joystick cable. See figure 5 on page 14.
6. Lift the backrest angle adjustment lever (See figure 4 on page 14) and while holding

the lever, lift the seat back to an upright angle, then release the lever to lock the seat
back in place.

REMOVAL
1.

With one hand brace the seat back. With the other hand lift the backrest angle

adjustment lever and while holding the lever, lower the seat back flat against the seat.

Lifting the Backrest Angle Adjustment Lever will cause the back to

automatically close towards the seat. Improper handling may result in injury.

2. Disconnect the cable from the joystick. See figure 5 on page 14.

3. Remove the arms by loosening the arm width adjustment knobs, then slide each arm
out to remove. See figure 18 on page 20.
4. Lift the seat up and off the seat post receiver.

«
...
11
12
13
14
15
...
»

Содержание Compass Sport GP605 CC





































Отзывы:

Нет отзывов