background image

11 

 

III. EMI/RFI

 

                                                                                                                                          
The rapid development of electronics, especially in the area of communications, has    

saturated our environment with electromagnetic (radio) waves that are emitted by        
television transmitters, cellular phones, citizen’s band radios (CBs) amateur radios (HAM 
radios), wireless computer links, microwave transmitters, paging transmitters, etc. These 
electromagnetic (EM) waves are invisible and increase in strength the closer one gets to 
the source of transmission. When these energy waves act upon electrical devices and 

cause them to malfunction or to function in an erratic or uncontrolled manner, they are 
referred to as Electromagnetic Interference (EMI) or Radio Frequency Interference (RFI). 

 
EMI/RFI AND YOUR 

Alanté

 

                                                                                                       

All electrically powered vehicles, including power chairs are susceptible to EMI/RFI. This 
interference could result in abnormal or unintended movement of your 

Golden

 

Alanté . 

 Unintended movement or brake release could cause an accident 

or  injury. 

                                                                                                                                                     
The FDA has determined that each make and model of power chair can resist EMI/RFI to           
a certain level. The higher the level of immunity, the greater the degree of protection from 

EMI/RFI measured in volts per meter (V/m). The FDA has also determined that current 
technology is capable of providing 20 V/m of immunity to EMI/RFI, which would provide 
useful protection against common sources of interference. This product has been tested 
and has passed an immunity level of 20 V/m. 

 

EMI/RFI RECOMMENDATIONS 
                                                                                                             

 

                       

PROHIBITED! 

Do not turn on or use hand-held personal electronic               

                        communication devices such as cellular phones, walkie-talkies, or CB   
                        radios while your power chair is turned on.  
• Be aware of any nearby transmitters (radio, television, microwave, etc.) on your  
intended route and avoid operation your of power chair close to any of those  
transmitters.  

• Turn off the power if your 

Alanté 

is going to be in a stationary position for any length of 

time.  
• Be aware that adding accessories or components or modifying your power chair may 
make it more susceptible to EMI/RFI.                                                                                           
• If unintended movement or brake release occurs, turn your power chair off as soon as 

it is safe to do so.                                                                                                                          
• Report all incidents of unintended movement or brake failure to your Golden  
Technologies representative or to Golden Technologies. 

 TURN OFF YOUR POWER CHAIR AS SOON AS IT IS SAFELY    

POSSIBLE IF UNINTENDED OR UNCONTROLLABLE MOTION OCCURS OR IF        
UNINTENDED BRAKE RELEASE OCCURS. 

Содержание Alante GP205















































Отзывы: