background image

OWNER’S MANUAL

page 46

PRODUCT REGISTRATION

PRODUCT REGISTRATION

We recommend to register the unit on our
internet website within 15 days from the
purchase at www.goldnote.it/product-registration

If the unit is not registered correctly or has been
purchased from a different country of the
purchaser home address the unit will not be
covered by any warranty and the registration will
be refused.
Please note that the warranty does not cover in
any case: Tubes, Phono Cartridge Stylus and
Batteries.

WARRANTY

All Gold Note products come with a
warranty against defective materials and
workmanship.
Any service and inspection must be carried
out by a Gold Note dealer or distributor so
in case you need any assistance with this
product, please contact the seller.
If you experience any problems locating
your official Gold Note dealer or distributor,
please check our website or contact
[email protected]

PLEASE NOTE
Descriptions and technical characteristics
may vary at any time and without notice.

WARNING

Gold Note products should only be opened,
serviced and inspected by certified Gold
Note technicians and dealers.
Work performed by unqualified personnel
may cause serious damage or personal
injury. Opening of the product by non-
authorised personnel will void the
guarantee.
In this case, contact your dealer to be
advised on how the fault can be solved.
Do not return any object directly to the
factory or to the distributor without being
authorised to do so.

www.goldnote.it/product-registration

Содержание Bellagio Conquest





















































Отзывы: