background image

 
Tornado SHO 

Model No. 3007, 3007A, 3007EX 

 

Page 12 

 

 

gmpopcorn.com

Shut Down Procedure/ 

Care and Cleaning 

Shut Down Procedure  

When completing operation for the day (or any prolonged period), run all the sugar out of the 
floss head. When empty, turn the heat to highest position for approximately one minute to 
“clean” the band by baking off remaining sugar. 

NEVER put water in the floss head.

 

Care and Cleaning 

 

 DANGER

 

Machine must be properly grounded to prevent electrical shock to personnel. 

DO NOT immerse in water. 

DO NOT clean appliance with a water jet.

 

Always unplug the equipment before cleaning or servicing. 

025_111616 

 

 

 

WARNING

 

Burn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or 
servicing. Avoid contact with molten sugar. 

006_092414 

 
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only 
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of 
advertising your product. 

Follow the directions below to clean and sanitize the unit each day after use. 

1.

 

Unplug the machine and wait for the floss head to cool down to room temperature. 

2.

 

Make sure to clean all pans/accessories in order to sanitize them before each use. 

3.

 

Wipe all surfaces with a clean, damp cloth. 

4.

 

Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless 
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).  

DO NOT

 use oven cleaners or abrasive materials as they will damage parts of the 

machine. 

 

 

Содержание Tornado SHO 3007































Отзывы: