manualshive.com logo in svg

GOG G-1, Инструкции по эксплуатации и настройке

Поделиться
Скачать
GOG G-1 Скачать руководство пользователя страница 22

                                        GOGpaintball.com   

TECH SUPPORT

Our  Technical  Support  Department  can 

provide assistance via telephone. See our web 

site for phone number and tech support hours. 

Additional support and downloadable product 

manuals are available through our website at 

GOGPaintball.com

MARKER WILL TURN ON BUT WILL NOT FIRE

• Battery may be low or dead – replace with fresh name brand alkaline battery.
• The trigger adjustment screw may be set in too far, preventing the trigger from resetting. 

See the trigger adjustment section of this manual for guidance.

• Trigger switch may be damaged. Contact your dealer or GOG Paintball

TM

 technical 

support.

• Regulator output pressure may be too high. Adjust the velocity to its lowest limit, then 

follow the velocity adjustment procedure in this manual.

•  Liquid  CO

2

  may  be  entering  the  valve  –  see  the  gasses  section  of  this  manual  for 

guidance in proper CO

2

 set-up.

MARKER IS BREAKING PAINT

• Use only fresh, high-quality paintballs. Poor quality paint, or paint damaged by humidity 

or temperature extremes during shipping or storage, will nor perform well.

• Ball detents may be worn or damaged. Inspect, and if necessary, replace following the 

disassembly instructions in this manual.

•  If  the  marker  is  equipped  with  an  upgraded

 

circuit  board  with  anti-chop  eye,  the 

anti-chop function may be turned off. Turn anti-chop on, following the upgrade circuit 
board’s instructions.

WARRANTY

GOG  Paintball  SA  warrants  for  (1)  year  to  initial  retail 

purchaser that the paintball marker and regulator are free 

from  defects  in  materials  and  workmanship.    Disposable 
parts  (batteries,  o-rings,  springs,  seals,  etc.)  are  not 

warranted.  The valve assembly, solenoid and electronics 
are warranted for 6 months.  This warranty does not cover 

surface damages (scratches and nicks), misuse, improper 

disassembly  and  re-assembly,  attempts  made  to  drill 
holes  or  remove  metal  from  the  external  surfaces  which 
could  degrade  performance  and  reduce  pressure  safety 

factors of the marker.  Do not make changes to the basic 

marker parts without written approval.  The only authorized 

lubricant for the marker is DOW 33 lubricant.  Use of any 

other  lubricant  could  result  in  voiding  your  warranty.  
Paintball  markers  are  non-refundable.    This  warranty 
is  limited  to  the  repair  or  replacement  of  defective  parts 
with the customer to pay shipping costs.  This warranty is 
effective only if the customer registers the product online 

@ gogpaintball.com within 30 days of the purchasing the 
marker.  The warranty is non-transferrable.  Do not attempt 

to alter the trigger assembly in any way, as this will void 
your  GOG  warranty.    Trigger  alteration  of  any  kind  may 
result in serious injury. 

TROUBLESHOOTING

IMPORTANT

20

Содержание G-1






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды