mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
to
.
1
M
CH
S
%
mask
sec
to
.
1
speed
Multi
CH
S
%
mask
sec
to
.
1
speed
Multi
CH
S
%
mask
sec
to
.
1
speed
Multi
CH
S
%
In this mode, you can set the flash output from 1/128th power to 1/8th power in 0.3 stop increments. With
stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject
in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number
of flashes, and the flash output.
1/8
1/16(+0.3
、+
0
.
7)
1/32(+0.3
、+
0
.
7)
1/64(+0.3
、+
0
.
7)
1/128(+0.3
、+
0
.
7)
1
7
14
30
60
99
2
6
14
30
60
99
3
5
12
30
60
90
4
4
10
20
50
80
5
4
8
20
50
80
6-7
3
6
20
40
70
8-9
3
5
10
30
60
10
2
4
8
20
50
11
2
4
8
20
40
12-14
2
4
8
20
40
15-19
2
4
8
18
35
20-30
2
4
8
16
30
- 25 -
- 26 -
Multi: Stroboscopic Flash
●
With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
●
Multi flash mode cannot be set in high-speed sync mode.
●
With high-speed sync, the color temperature is lower (decrease around 700K) because of tube’s characteristics.
Please set the camera to AWB (Auto White Balance).
Set the flash frequency and flash
3
times.
● Press <
SET
> Button to select
the flash times. Turn the Select
Dial to set the number.
● Press <
SET
> Button to select
the flash frequency. Turn the
Select Dial to set the number.
Press <
MODE
> button so that
1
<
Multi
> is displayed.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the
shutter speed and set it with the camera.
Number of Flashes / Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2
seconds.
●
Stroboscopic flash is most effective with a highly reflective subject against a dark background.
●
Using a tripod and a remote control is recommended.
●
A flash output of 1/1 and 1/2 cannot be set for stroboscopic flash.
●
If the number of flashes is displayed as “--”, the firing will continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown by the following table.
Maximum Stroboscopic Flashes:
Flash Output
Hz
Turn the Select Dial to choose
2
a desired flash output.
QuickerII adopts built-in 2.4G wireless X system, which is perfectly compatible with other products of our company.
Nikon cameras (using X1T-N, TT685N, etc.) and Canon cameras (using X1T-C, TT685C, etc.) can enjoy one or
more QuickerII together.
*
As a slave unit, QuickerII can be controlled by the master unit e.g. AD360II-C, AD360II-N, TT685C, TT685N, X1T-
C, X1T-N, TT600, etc.
Setting the Communication Group
Wireless Flash Shooting
:
Radio (2.4G) Transmission
Wireless Settings
Press < > Wireless Button so that < > is displayed, entering the 2.4G wireless status now.
Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the channel IDs to prevent
signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same.
Long press the <
GR/CH
>
1
Button for 2 seconds until
the channel IDs is blinking.
Turn the Select Dial to choose
2
the channel from 1 to 32.
Press the <
SET
> Button to confirm.
3
Short press the <
GR/CH
>
1
Button for 2 seconds until
the group IDs is blinking.
Turn the Select Dial to choose
2
the group from 0 to F.
Press the <
SET
> Button to confirm.
3
