Assembly
To fit the hose to the cleaner, insert the hose
end into the hose inlet
‹
until it clips securely
into position.
Attach the extension tubes to the handle end
of the hose. The hose handle features a regulator
which allows the suction to be reduced as
required.
Attaching the accessories
Fit the floor nozzle onto the end of the
extension tube. The hard floor attachment
(certain models) can be attached to the floor
nozzle, to facilitate vacuuming hard floors.
Other accessories are stored in the back of the
cleaner and include:
• upholstery nozzle for stairs, furniture;
• crevice tool for awkward places, behind
radiators etc.
Automatic cable rewind (certain models)
Reel out the cable fully. After use, unplug and
press the foot pedal
fl
, holding the plug until fully
rewound.
On/off
The on/off control is operated by the foot
pedal
‡
.
Electronic suction regulator (certain models)
This is a rotating knob
·
which allows the
suction power of the cleaner to be set at the
precise level required. For example:
• turn fully clockwise for maximum suction
for carpets, hard floors etc.
• turn anti-clockwise for reduced suction
for upholstery and curtains.
Stair Lock (certain models)
This unique device (patent applied for) assists
with stair cleaning. The special bracket
‚
, found
underneath, is lifted out as shown
B
and locked
onto the stairs. In addition, the rear wheels are
locked in position as further security. After use,
simply push firmly back into position.
Please note
When cleaning on stairs, for convenience and
safety, work from the bottom to the top with the
upholstery nozzle or crevice tool connected
directly onto
the hose
handle. It is
recommended
that the
extension tubes
are
not
used.
Using your Goblin vacuum cleaner
B
Replacing/emptying the dustbag
To obtain the best results from your cleaner be
sure to change the dustbag when necessary,
otherwise the airflow and cleaning power will be
reduced.
When the dustbag condition indicator
›
shows
fully red and performance deteriorates, first check
if there are any blockages in the accessories or
tubes. If these are clear, it is necessary to
replace/empty the dustbag.
Paper dustbags
1
Remove the hose end from the hose inlet.
2
Slide the dustbag compartment lid release
¤
,
lift and remove the cover.
3
Pull the tab to close the opening to prevent dust
spillage
C
.
4
Remove the dustbag from its location by pulling
the dustbag securing tab
„
as shown
D
.
5
Insert the new dustbag into position ensuring
the cardboard collar is firmly secured at the base
as shown
E.
6
Pull forward as shown
F
so it locks under the
plastic securing tab at the top.
7
The folds of the dustbag should be opened out.
8
Relocate the lid at the front (carrying handle
⁄
)
end first and then close the cover securely.
Note:
The securing tab
„
prevents the cover
being closed unless a dustbag is fitted correctly.
Permanent dustbag
1
Remove the hose end from the hose inlet.
2
Slide the dustbag compartment lid release
¤
,
lift and remove the cover.
3
Pull the tab to close the opening to prevent dust
spillage
C
.
4
Remove the dustbag from its location by pulling
the dustbag securing tab
„
as shown
D
.
5
Hold the dustbag over a dustbin and slide the
clip from the bottom of the bag and shake the
contents of the bag carefully into the bin.
6
Slide the clip back onto the bottom of the
dustbag and replace the dustbag into position
ensuring the collar is firmly secured at the
base
E
.
7
Pull forward as shown
F
so it locks under the
plastic securing tab at the top.
8
The folds of the dustbag should be opened out.
9
Relocate the lid at the front (carrying handle
⁄
)
end first and then close the cover securely.
Note
The securing tab
„
prevents the cover
being closed unless a dustbag is fitted correctly.
10
We recommend that the bag is washed in warm
water every six months or sooner if it becomes
particularly dirty. Allow to dry naturally as direct
heat may effect the material.
Important
Ensure the dustbag is totally dry
before installing it back into your vacuum
cleaner.
Replacement Dust Collection Bags
These are available from Goblin or from your
local service agent - see back cover for details.
Cleaning and replacing the filters
Motor protection filter
‰
This is in the dustbag compartment. Clean it
everytime you change the dustbag and replace it
after approximately 5 dustbag changes.
1
Lift out the red filter as shown
G
and clean by
tapping.
2
Replace the filter by sliding it into position as
shown
H
.
Note
The safety catch
Â
prevents the cover
being closed unless a motor protection filter is
fitted.
Exhaust filter
Ê
This is located on top of the motor housing
J
.
Clean it everytime you change the dustbag and
replace it after approximately 5 dustbag changes.
To remove, lift it from its location and shake to
clean or replace.
The floor nozzle can be secured on the
underside of the cleaner when it is stood on end
by locating the bracket found on the nozzle into
the slot provided.
Storage
Ê
Care and maintenance
ALWAYS DISCONNECT FROM THE MAINS BEFORE
WORKING ON OR CLEANING YOUR CLEANER.
Your cleaner is manufactured to withstand
normal day-to-day use, but an occasional wipe over
with a damp cloth will help maintain its good
looks.
Abrasive cleaners should not be used.
C
D
E
F
G
H
J
K