GOALRILLA DC72E1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 18

background image

Use the Backboard Pads as a Template and mark the hole locations on the backboard frame.

Note: Safety glasses required for Step 25.

Drill 9/64 pilot holes through aluminum trim and into Steel backboard frame as shown in

Detail C

.

DO

NOT

drill through both sides of tube.

Note: Cordless drill recommended for screw installation. Do not over tighten screws causing
screws to strip.
Note: To install screws, it will be easier if you use a cordless drill with 5/16” socket (instead of
Phillips head.)

Secure Backboard pads using screws provided (

#51

) as shown in

Figure 13

.

24.

25.

26.

Figure 12

23.

Adjust unit to lowest position. Use a tape measure to measure
from the top of the rim to the playing surface. Stick Height Decal
(#17) to back of Actuator (#16) with the measured height mark
aligned with bottom of Actuator Sleeve (#15). See Figure 12.

16

17

12

Grease fitting

Detail C

Backboard

Pads (# 48 & 49)

Mounting Screw

(# 51)

51

51

51

48

49

*Rim not

shown for

clarity.

Figure 13

«
...
10
11
12
13
14
...
»

Содержание DC72E1



















Отзывы:

Нет отзывов

Похожие инструкции для DC72E1

Бренд: Waterpik Страницы: 20

Water Flosser WF-06

Бренд: Waterpik Страницы: 2

Бренд: Waterpik Страницы: 6

Бренд: Waterpik Страницы: 24

Бренд: Panasonic Страницы: 2

Бренд: Harol Страницы: 16

Бренд: Camtraptions Страницы: 10

Бренд: Avanti Страницы: 28

Бренд: FAAM Страницы: 19

Бренд: Banner Страницы: 22

Бренд: Land Pride Страницы: 10

Бренд: La Crosse Technology Страницы: 2

Бренд: SciQuip Страницы: 24

Бренд: Kanvus Страницы: 78

Бренд: Blaupunkt Страницы: 13

Real Life Ninja Starter Pack 1

Бренд: DGS Страницы: 8

Power Adaptor 87020

Бренд: Nyko Страницы: 1

Ultrasonic LoRaWAN

Бренд: TEKELEK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды