GO-DEVIL Surface Drive Скачать руководство пользователя страница 26

W a r r a n t y  

This warranty replaces any warranties before August 1, 2011 

 

 

Go-Devil  Manufacturers  of  Louisiana,  Inc.  will  repair  or  replace  any 

components,  on  the  Go-Devil  drive  unit  that  we  manufacture  at  no  charge  for  a 

period of two years that are defective in materials or workmanship.  Transportation 

charges  on parts submitted  for  repair or  replacement under this  warranty  must be 

borne by the owner of the unit.  This warranty does not cover normal wear, abuse, 

neglect, or failure due to the elements of nature, such as salt water corrosion.  Wear 

on  shaft  and/or bushing  due to the  lack  of  lubrication  will not be  covered by  this 

warranty!  See your Service Manual for the proper lubrication instructions. 

 

Kohler and Honda Engines on our products have a two year engine warranty 

that  is  applicable  as  long  as  the  original  owner  owns  the  unit.  Briggs  &  Stratton 

Vanguard  engines  have  a  three  year  warranty  as  of  July  2010  and  as  long  as  the 

original owner owns the unit. All Briggs & Stratton Vanguard engines sold before 

July 2010 have a two year warranty. 

 

Engine  warranty  can  be  handled  through  any  small  engine  dealer  in  your 

area that is an authorized warranty service dealer for the brand of engine that you 

have  on  your  unit.    Go-Devil  Manufacturers  of  Louisiana,  Inc.  is  authorized  to 

warranty  all  the  engines  that  we  sell  on  our  products.    In  many  cases,  we  can 

expedite a repair by sending the part to you, because most warranty repairs are as 

simple  as  replacing  a  simple  part.    You  will  however,  be  required  to  return  the 

defective part to us.  At that point, we will file the warranty claim directly to the 

engine manufacturer at no charge to you. 

Содержание Surface Drive



























Отзывы: