GMT GMT 050 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 42

GMT GMT 050 Скачать руководство пользователя страница 21

GMT 050

User manual

21

Now simple release the activation button and the tree part will tilt-down smoothly. Releasing the
button on the remote control will deactivate all the brakes and tilt-block.

Release the brake

The whole unit including the link will now behave as a standard GMT felling grapple. Allowing the link
to move freely in all directions and the tilt-cylinder to tilt-down again.

Safety instruction

prevent the GMT TTC set getting damaged!!!

When the tree piece to be cut is of considerable weight or length and aiming upright more than 30

degrees the TTC system must be activated during cutting!

Following work sequence must be followed with TTC-system activated:

1.

Take tree piece out of the canopy

2.

Rotate tree piece in front of the crane

3.

Tilt-down crane (extension) arm

4.

Release the brake

5.

Open grapple to drop tree piece

lowered tree

During tilt-down tree piece could slowly swing down horizontal with brakes still activated. This is
perfect! Bringing tree piece as horizontal as possible prevents shock loads to the system and
damaging of TTC-system components.

«
...
19
20
21
22
23
...
»

Содержание GMT 050











































Отзывы:

Нет отзывов