manualshive.com logo in svg

GMP Air Stream 89300, Эксплуатация и обслуживание

Поделиться
Скачать
GMP Air Stream 89300 Скачать руководство пользователя страница 5

Page 5 of 41 

been installed into the tube. 

23.  Ensure the cable drum rotates freely on its stand, the cable should leave from the top of the drum. 
24.  The cable should enter the machine in a clean and dry condition.  In damp, dusty atmospheres, the cable 

should be cleaned continuously as it enters the machine. 

 

FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY, AS THE CABLE 

COULD BE EJECTED FROM THE CABLE BLOWING MACHINE WITH HIGH 

FORCE AND VELOCITY. 

 

If the connecting plug on the power lead to the generator / (or supply) supplied with the Airstream machine is 

unsuitable and requires replacement, the new plug must be correctly connected observing the color codes as 

below. 

 

IT IS THE RESPONSIBILITY OF THE USER TO ENSURE THAT THE CONNECTIONS MEET THE 

ELECTRICAL REGULATIONS FOR THE RELEVANT COUNTRY. 

 

Brown (Live) 

Yellow & Green (Earth) 

Blue (Neutral) 

Black (Live) 

White (Neutral) 

Green (Earth) 

Alternative Wiring 

Содержание Air Stream 89300










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды