background image

PAGE 22  

INSTRUCTION MANUAL 

TX4400

GENERAL

 

Compliance: 

Compliant with AS/NZS 4365     

 

  for radio communications 

 

  equipment in the UHF citizen  

 

  band and personal radio service .

 

Frequency Range: 

476 .425 MHz - 477 .400 MHz

  Number of Channels: 

40 (plus 20 receive only)

 

Frequency Range  

 

(receive only): 

465 MHz - 485 MHz

 

Channel Spacing: 

25 kHz

 

Operating Mode: 

Simplex or half duplex with  

 

  repeater talk-around .

 

Scanning Speed: 

100 ms per channel (10  

 

  channels per second)

  Antenna Impedance: 

50 Ohms nominal

 

Nominal Battery  

 

Voltage: 

12 V DC

 

Operating Voltage  

 

Range: 

10 to 16 V DC

 Standard Test Voltage: 

13 .8 V DC

 

Battery Polarity: 

Negative Earth

 

Overvoltage  

 

Protection: 

30 V DC maximum - At 18 V DC  

 

  the RF power is reduced and 

 

  the channel display flashes 

 

  ‘Hi DC’ on receive .

 

Reverse Voltage 

 

Protection: 

Diode Crowbar

  

Overcurrent protection:

 

In-line 2 Amp fuse

  Operating Temperature:

 

-10° C to 60° C

TRANSMITTER

 

RF Output:

  5 Watts

 

Spurious Emission: 

< - 70 dBc

 

Frequency Error: 

< ± 5 PPM

 

Modulation: 

FM

  Maximum Deviation: 

< ± 5 kHz at + 20 dB AF  

 

  Limiting

  Transmit Frequency  
 

Response: 

+ 6 dB per octave 300 Hz to 3  

 

  kHz, + 1, - 3 dB

  Demodulated Audio  
 

Signal to Noise: 

> 45 dB unweighted .

 Current Consumption: 

1 .4 Amps with 50 Ohm  

 

  termination .

RECEIVER

 

RF Bandwidth: 

< 5 MHz

 

Intermediate 

 

 Frequencies: 

21 .4 MHz and 455 kHz

 

Sensitivity: 

- 123 dBm for 12 dB SINAD  

 

  unweighted .

 

Sensitivity of  

Receive-only Channels: 

-107 dBm for 12 dB SINAD

 

Selectivity: 

- 6 dB ± 7 .5 kHz

 

  - 70 dB ± 25 kHz

 

Intermodulation  

 

Immunity: 

76 dB

  Blocking Immunity:

  >100 dB

 

Spurious Response  

 

Immunity:

  70 dB

  Audio Output Power: 

3 Watts average into 4 Ohms .

 Audio Signal to Noise: 

> 45 dB unweighted

  Receiver Frequency  
 

Response: 

- 6 dB per octave de-emphasis,  

 

  300 Hz to 3 kHz, + 1, - 3 dB .

 Current Consumption: 

210 mA muted .

 

  600 mA Full Volume .

  Conducted Spurious  
 

Emission: 

< - 75 dBm

 

Squelch: 

Adjustable -125 dBm to 

 

  -109 dBm . Max . Hysteresis 

 

  6 dB typical .

MECHANICAL SPECIFICATION & 

CONNECTIONS

 

Dimensions: 

172 mm (W) x 95 mm (D) x  

 

  52 mm (H)

 

Weight: 

626 grams

 12 Volt Power Supply: 

Two core red and black cable  

 

  with bulkhead connector in rear  

 

  panel .

 

Antenna: 

SO239 panel socket

 

External Speaker: 

3 .5 mm Mono Jack

 

Microphone Port: 

6 Way telephone style with  

 

  rubber strain relief . 

SPECIFICATIONS

Содержание TX4400

























Отзывы: