GMC MX1275 Скачать руководство пользователя страница 10

Using the parallel fence guide

The parallel fence allows you to make parallel cuts in a 

sheet of wood, all at the same width.

Caution.

 Always ensure that the saw is switched off and 

unplugged from the power supply before making any 

adjustments.
1.  Slide the parallel fence (9) through the slots in the 

base plate.

2.  Adjust the guide to the required width and secure it in 

position with the locking knob (8).

3.  Ensure that the guide rests against the wood along its 

entire length to give a consistent parallel cut.

Dust extraction

You can connect the tool to a vacuum system via the dust 

extraction port (14).

Changing the blade

Caution.

 Always ensure that the saw is switched off and 

unplugged from the power supply before making any 

adjustments.
1.  Rotate the saw blade by 

hand whilst depressing the 

spindle lock button (17) 

until the blade locks.

2.  Turn the blade bolt anti-clockwise using the hex key 

(20) provided.

3.  Remove the outer blade flange and the blade bolt.
4. Retract the lower blade guard (11) using  

  the lever (10).
5. Remove the saw blade from 

the inner flange and pull it out.
6. Clean the saw blade flanges 

thoroughly before mounting the 

new saw blade.
7. Mount the new saw blade in 

reverse order and tighten the 

blade bolt.

Warning.

 The direction in 

which the blade rotates has to be the same as the 

direction of the arrow marked on the housing.
8.  Ensure that the spindle lock button (17) is released.
9.  Before using the saw again, check that the safety 

devices are in good working order.

Important.

 After replacing the saw blade, make sure that 

the saw blade runs freely by turning the blade by hand.

WARNING:

 Plug the machine in to a power socket and 

run the saw under no load to check that it runs smoothly 

before using it to cut any material.

10

Содержание MX1275













Отзывы: