GMC LDP13F12 Скачать руководство пользователя страница 20

20

Carefully read the entire Instruction Manual 

before using this product.

Before returning this product for a 
Warranty Claim or any other reason 

Please Call 1300 880 001 (Australia)
or 0800 445 721 (New Zealand)

When you make your call, please have 
the following information at hand: 

• 

GMC Product Type  

 GMC Product Code

A GMC Service Engineer will take your call and, in 
most cases, will be able to solve your problem over 
the phone. 
You are welcome to use this phone-in service to 
make suggestions or give comments about any 
GMC product.

With continuing product development changes may 
have occurred which render the product received 
slightly different to that shown in this instruction 
manual. The manufacturer reserves the right to 
change specifications without notice. Note: 
Specifications may differ from country to country.

The GMC 777 Helpline operates from 7am to 

7pm, 7 days a week (EST). This allows you 

to contact GMC directly with any queries and 

technical questions you have regarding 

our products.

45–55 South Centre Road 
Melbourne Airport
Victoria, Australia 3045
Tel: (03) 8346 1100  Fax: (03) 8346 1200

Save this Manual for future reference.

Содержание LDP13F12





















Отзывы: