GMC LD108V Скачать руководство пользователя страница 11

11

Battery charging 

IMPORTANT.

 Before plugging in the power supply from the 

charger adaptor (9) to the charger base (10) always ensure 

that the plug is switched off at the mains.

IMPORTANT.

 The battery will be fully charged after  

3-5 hours, remove it from the charger after this time.  

Do not leave a battery charging for longer than 24 hours. 
1. Align the battery pack (5) with 

the charger base (10) as per 

the picture shown. Insert the 

battery pack (5) and slide it 

firmly into position as shown. 

Note:

 If the battery pack is 

incorrectly orientated the battery 

will not fully enter the base as 

depicted.

2. Connect the power supply 

from the charger adaptor (9) 

to the charger base (10) via 

plugging the socket from the 

charger adaptor (9) into the 

side of the charger base (10) 

housing.

3. Plug in the charger and switch 

on at the power supply. The 

red LED indicator located on the charger base (10) will 

indicate that the charger base has power connected to it.  

The flashing lights on the battery pack will indicate the 

battery status while the battery is charging. Refer to the 

below table:

Battery indicator while charging

Status

Red 

LED

Yellow 

LED

Green 

LED

Charging status/indicator description

Charging

ON 

FLASH  FLASH  Yellow and green LED lights flash one after the other during the 3 – 5 hour 

charging duration

Fully 

charged

OFF 

OFF 

ON 

Battery pack is fully charged

High 

temperature 

or defective

OFF 

ON 

OFF 

High temperature. The battery pack temperature is too high and needs 

to be cooled down. Once the battery pack has been cooled down to an 

appropriate level the battery will continue to charge.
If the battery pack cools down and the status remains unchanged then  

the battery pack is defective/damaged and should not be used. 

WARNING:

 Never use a damaged battery pack.

Battery 

conditioning 

or defective

OFF 

OFF 

OFF 

Battery conditioning occurs when the battery pack has low charge left in 

its cells. It may take around 90 minutes for the battery to be conditioned 

before commencing the charging process.
If the status remains unchanged then the battery pack is defective/

damaged and should not be used.

WARNING:

 Never use a damaged battery pack.

Содержание LD108V

















Отзывы: