1. 1-24 channel output connector
25-pin 'D' socket
2. 25-48 channel output connector
25-pin 'D' socket
3. 49-72 channel output connector
25-pin 'D' socket
4. Output level: 10V, 12V and 15V are available by changing
the setting of 4-dipswitches.(see right figure.)
5. Analogue output polarity: Move to the left for "+" output,
right for "-" output. (see right figure.)
6. Power input: AC 230V~50Hz, 1A
1. Turn the power switch on.
2. Press MENU button for 3 seconds to enter mode setting.
MODE SELECT
press UP/ DOWN button to select DMX or MIDI MODE, the matching led blinks,
then press MENU button.
DMX MODE
When DMX led blinks, the 7 segment display shows the blinking DMX initial
address(
), press UP/DOWN button to select desired address and
then press MENU button again.
MIDI MODE
When MIDI led blinks, the 7 segment display shows the blinking channel NO.
(
), press UP/DOWN button to select desired channel, press MENU
button again
HOLD MODE
When the 7 segment display shows ON/OFF, the HOLD led is lit, press UP/
DOWN button to select ON or OFF. If it shows ON, the last scene remains when
DMX disappears; if it shows OFF, the last scene doesn't remain.
SPEED SETTING
Press MENU button once more, the 7 segment display shows
, press
UP/DOWN button to select desired chasing speed.
CHANNEL SETTING Press MENU button, the 7 segment display shows
, select desired
channel using UP/DOWN button, then press MENU button to confirm and leave
mode setting. If you select
, the 1-48 channel will be executed periodically
in the order.
3. When DMX led is lit, the 7 segment display shows the initial DMX address AXXX , and the 72 channel
DMX signals beginning from the AXXX are converted to 72 channel analogue output. When DMX signal
remains, the Signal led blinks.
4. When MIDI led is lit, the 7 segment display shows MIDI channel NO.(
), MIDI signals from
NOTE NO.(22-93) are converted to 72 channel analogue output. When MIDI signal remains, the Signal
led blinks.
5. When it is receiving DMX signal, after the scene setting is finished, press STORE button for 5 seconds
till
display, now you have stored a scene. Release the button to return to DMX input.
6. Press STORE button to run a pre-stored scene, the 7 segment display shows
. In mode setting,
this function is defeated.
7. Press CHASE button to enter CHASE mode, the 7 segment display shows
.
8. You have three options for analogue output: +(-)10V, +(-)12V & +(-)15V.
Be sure the dip switch 1 is always ON, set dip switch 2 to ON for 15V output, dip switch 3 ON for 12V
output, dip switch 4 ON for 10V output. Remember any two of dip switches 2, 3 and 4 may not be ON
at a time.
OPERATING INSTRUCTIONS
A001-A512
CH01-CH16
SP01-SP99
C-01-C-72
C-48
CH01-CH16
CHAS
UNDER A HIGH TEMPERATURE OR HUMIDITY AREA.
3. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPARATUS
2. DISCONNECT THE POWER CABLE BEFORE OPENING.
1. THIS APPARATUS MUST BE EARTHED.
WARNING!!!
1
2
3
5
4
6
OUTPUTS 1-24
1
24
Earth
OUTPUTS 25-48
25
48
Earth
OUTPUTS 49-72
49
72
Earth
+
-
ANALOG OUTPUT
POLARITY
OUTPUT LEVEL
DIP Switch
Output
15V
12V
10V
on
on
on
on
on
on
off
off
off
off
off
off
4
3
2
1
N'OUVREZ PAS..RISQUE DE CHOCELECTRIQUE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
THIS APPARATUS MUST BE EARTHED
