background image

 

1

Expandable Depth Wall Safe

050619

globalindustrial.ca

User's manual

Manual del usuario

Manuel de l'utilisateur

Customer Service

US: 1-800-645-2986

Servicio de atención al Cliente

US: 1-800-645-2986

Service à la clientèle

Canada: 888-645-2986

Model 493492

        CAUTION

Before the safe is installed, change the locks combination 

to a number sequence other than the factory preset code 

of 1-5-9 to ensure security. Do not keep the keys in  

the wall safe.

Opening The Safe For The First Time

Use the override/emergency key to open the safe.
1.  Remove the round plastic cap on the panel to locate 

the key lock.

2.  Insert the key and turn counterclockwise.
3. Pull the handle and open the safe.

Installing or Changing Batteries

1. Open the safe to locate the battery compartment.
2. Remove the battery box cover.
3. Insert 4 new AA batteries (not included).
4. Replace battery box cover.
5. Test the code before locking the safe door.

Low Battery Warning:

 If the batteries are low, a red light 

will appear when the keypad is pressed. If the batteries are 

drained, open the safe using the override/emergency key.

Programing The Digital Combination Lock

Changing the 1st user code (code length:1-8 digit code)

1. Enter the factory preset code: 1+5+9+B on the keypad.
2. Open the door by pulling the chrome handle.
3.  Press the reset button on the inside of the door (near 

the door hinges). There will be a beep and a yellow 

light will appear on the keypad for 10-15 seconds.

4.  Before the yellow light disappears enter a new code 

and press the “A” key. The new code must be between 

3 to 8 digits. If the code is valid, the keypad will beep 4 

times. If you have failed to set a code or a wrong code 

has been entered, wait for the yellow light to disappear 

and repeat above steps 1-4.

        WARNING

Test the new code several times (CODE+"B") before 

closing and locking the door.

Security Lockout

If the incorrect code has been entered three times, the 

keypad will lock for 5 minutes. You must wait over 5 

minutes before being able to access the safe.

Override Keys To Open The Safe

In case of a forgotten password or if the batteries run 

out, there is an override lock system to open the safe.  

Remove the round plastic cap on the panel to locate the 

key lock. Insert the key and turn counterclockwise and 

pull the handle to open the safe. Do not keep the keys in 

the wall safe.

Emergency Key

Interior Light Switch

Programming Button

Battery Compartment

Battery 

Compartment

Steel Locking Bolts

Interior Light

Please Read Entire Manual. 

Save For Future Reference.

Содержание 493492







Отзывы: