background image

AIR CONDITIONER FEATURES(CONTINUED)

TO SELECT THE
OPERATING MODE:

Press the Mode
button.

DO THIS:

To choose operating mode, press the Mode button.
Each time you press the button, a mode is selected
in a sequence that goes from Auto, Cool, Dry , Heat
(Cooling only models without) and Fan. The indicator

light beside will be illuminated and remained on

once the mode is selected.

NOTE:

To operate on Auto feature:

In this mode, the fan speed cannot be adjusted, it
starts automatically at a speed according to the
room temperature. If the room does not get too
warm, it will stay at Low speed.

To operate on Fan Only:

Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale
air(on some models). (Remember to open the vent
during this function, but keep it closed during
cooling for maximum cooling efficiency.) You can
choose any fan speed you prefer.
During this function, the display will show the actual
room temperature, not the set temperature as in the
cooling mode.

TO USE THE ENERGY
SAVER FEATURE:

Press the button

DO THIS:

In this mode, the fan will continue to run for 3 minutes
after the compressor shuts off. The fan then cycles
on for 2 minutes at 10 minute intervals until the room
temperature is above the set temperature, at which
time the compressor turns back on and cooling starts.

NOTE:

SLEEP FEATURE:

Press Sleep
button

DO THIS:

In this mode the selected temperature will increase by
2 degrees F 30 minutes after the mode is selected.
The temperature will then increase by another 2
degrees F after an additional 30 minutes. This new
temperature will be maintained for 7 hours before it
returns to the originally selected temperature. This
ends the Sleep mode and the unit will continue to
operate as originally programmed. The Sleep mode
program can be cancelled at any time during operation
by again pressing the Sleep button.

NOTE:

7

Energy

Saver

Sleep

Timer

Temp

Mode

Timer

Auto

Cool

On

Off

Temp

Sensing

Energy

Saver

Sleep

Timer

Temp

Mode

Timer

Auto

Cool

On

Off

Temp

Sensing

Energy

Saver

Sleep

Timer

Temp

Mode

Timer

Auto

Cool

On

Off

Temp

Sensing

Fan

Dry

Fan

Dry

Fan

Dry

Fan

Dry

Содержание 246540






























Отзывы: