background image

 

- 8 -

6.2 Answering incoming calls 

When a call is forwarded from the paired device to the headset, a ring tone will 
be heard at the earphone. Press TALK button to answer the call. Green LED 
will then flashes 4 times for every 3 seconds periodically. 

NOTE: 

If your headset is paired with NOKIA cellular phone. The phone will 

control the headset to auto-accept incoming calls after 2 rings. 
 
 

6.3   Earphone volume control 

 

Change volume 

z

 

Press Volume Up button to turn the volume up.   

z

 

Press Volume Down button to turn the volume down.   

 

Mute/Un-mute the microphone 

z

 

Press and hold either volume button for at least 2 seconds to mute. 
The headset will make a periodic low-tone beep warning that the 
microphone is muted. 

z

 

Press either volume button once to un-mute. 

 
 

6.4 Ending a call 

To finish a call, short-press TALK button or press the CANCEL button on the 
phone. Either button has to be pressed to release a call and also the 
connection with the paired device. 

 
 
6.5 Making a call 

To make calls using the headset, Voice Dialing needs to be used since there is 
no keyboard built on the headset. Please check if your phone supports Voice 
Dialing and then follow the phone’s user guide to record voice tags. 
 
The steps of making a call from the headset are: 
1. Press 

TALK 

button 

2.  Wait for a beep and then say the name of the person you want to call 
3.  Please refer to the previous sections for the instructions of earphone 

volume control and ending a call. 

 

Содержание GL2BHS83











Отзывы: