manualshive.com logo in svg

Global Hobby AK-18, Инструкция по эксплуатации

Поделиться
Скачать
Global Hobby AK-18 Скачать руководство пользователя страница 2

2

TABLE OF CONTENTS

To make your modeling experience totally enjoyable, we recommend that you get experienced, knowledgable help
with assembly and during your first flights.  Your local hobby shop has information about flying clubs in your area
whose membership includes qualified instructors.  You can also contact the AMA at the address below.

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN.  47302-9252

(800) 435-9262

www.modelaircraft.org

Global guarantees this kit to be free from defects in both material and workmanship, at the date of purchase.  This does
not cover any components parts damaged by use, misuse or modification.  In no case shall Global's liability exceed
the original cost of the purchased kit.

In that Global has no control over the final assembly or material used for final assembly, no liability shall be assumed
for any damage resulting from the use by the user of the final user-assembled product.  By the act of using the final
user-assembled product, the user accepts all resulting liability.

Fuel Tank.......................................................................14

Stopper Assembly..................................................14
Stopper Installation................................................15
Fuel Tank Installation.............................................15

Servo Installation...........................................................16

Installing the Fuselage Servos................................16

Throttle Connection.......................................................16

Installing the Throttle Connector............................16

Elevator Pushrod...........................................................16

Installing the Control Horns...................................16
Installing the Elevator Pushrod..............................17

Rudder Pushrod.............................................................17

Installing the Control Horn....................................17
Installing the Rudder Pushrod...............................18

Aileron Pushrods...........................................................19

Installing the Control Horns...................................19
Installing the Aileron Pushrods.............................19

Cowl..............................................................................19

Installing the Cowl Blocks....................................19
Mounting the Cowl.................................................20
Installing the Fuel Filler.........................................20
Installing the Fuel Lines........................................20

Canopy..........................................................................21

Canopy Preparation................................................21
Mounting the Canopy.............................................21

Final Assembly..............................................................21

Installing the Receiver and Battery........................21
Installing the Switch..............................................22

Balancing......................................................................22
Control Throws.............................................................22
Flight Preparation.........................................................22

Preflight Check......................................................22

Flying.............................................................................23
Notes..............................................................................24
Trim Chart......................................................................25
Product Evaluation Sheet..............................................27

Kit Contents....................................................................3

Additional Items Required..............................................4

Tools and Supplies Needed.............................................4

Field Support Equipment Needed...................................4

Metric Conversion Chart.................................................4

Wing Assembly................................................................5

Hinging the Ailerons................................................5

Installing the Aileron Servos...................................6

Installing the Servo Hatches....................................6

Installing the Dihedral Brace...................................7

Joining the Wing Halves..........................................8

Main Gear Installation....................................................8

Installing the Main Gear Wires................................8

Installing the Main Gear Wheels.............................9

Wing Mounting...............................................................9

Installing the Wing..................................................9

Installing the Wing Bolt Doubler.............................9

Horizontal Stabilizer Installation....................................9

Aligning the Horizontal Stabilizer...........................9

Mounting the Horizontal Stabilizer........................10

Hinging the Elevator Halves..................................10

Vertical Stabilizer Installation........................................11

Aligning the Vertical Stabilizer..............................11

Mounting the Vertical Stabilizer............................11

Hinging the Rudder................................................11

Nose Gear Installation...................................................11

Installing the Nose Gear Brackets..........................11

Installing the Steering Arm....................................12

Installing the Steering Pushrod..............................12

Installing the Nose Gear Wheel.............................13

Engine Installation.........................................................13

Mounting the Engine to the Beams........................13

Mounting the Engine to the Firewall......................13

Installing the Throttle Pushrod...............................14

Содержание AK-18





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды