manualshive.com logo in svg

Global Hobby AK-18, Инструкция по эксплуатации

Поделиться
Скачать
Global Hobby AK-18 Скачать руководство пользователя страница 1

1

Version         V1.0

12-99 MTN

 All Contents          © Copyright 1999, Global Hobby Distributors

Instructions for Final Assembly

The Yak-18 was designed by the Soviet Designed Bureau Yakovlev.  It was to be used as a

primary trainer in the Soviet Air Force.  Like many of the Soviet aircraft, the Yak-18 was built to withstand
the rigors of rough field takeoffs and demanding flying.  The Yak-18 was equipped with a powerful
radial engine and rugged tricycle landing gear, just for this purpose.  It's generous wing area, coupled
with excellent flight and ground handling qualities make the Yak-18 an excellent choice for modelers.

Now you too can experience what the full size Yak-18 might have been like with your new Global

Yak-18 ARF.  The Global Yak-18 is built by master craftsmen, utilizing the finest grades of balsa,
light ply, foam and fiberglass.  It's covered using heat shrink polyester covering material, just like
you would use if you were building it yourself.  A complete set of high quality hardware is in the box.
This includes the fuel tank, wheels, pushrods, clevises and much more.  Even a high quality composite
10 x 6 propeller is included.  Don't worry about having to buy a quality aftermarket cowl to replace the
cheap plastic one that comes in some ARF's.  We've provided a one piece fiberglass cowl that's
painted to match the covering!  The scale debris screen is even molded in.  With this kind of quality
prefabrication, you'll be in the air and enjoying your new Yak-18 in no time!

.36 -.46 Sport Scale ARF

Содержание AK-18





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды