USING THE JUICER
Mount the juicer body & pulp collector on the basic unit.
Place the juicer mesh into the juicer body. Ensure that the
mesh sits properly and locks the lower coupler of the basic
unit. If necessary push down slightly or rotate the mesh a
little. Don’t apply any undue pressure. The mesh is a very fine
and precisely balanced component.
Slide the juicer spout (outlet) cover in position and press.
Mount the juicer cover onto the juicer body and lock the
clamps, plug the cord in and the juicer is ready for use. Press
the switch marked ‘pulse’ to check if the filter mesh assembly
is properly seated with the lower coupler of the basic unit.
The mesh should spin evenly without wobbling. Wash
ingredients and cut Suitably to fit feeder opening.
Place a glass under the spout. Set switch to position “1”.
Push ingredients into the feeder with the food pusher.
Check that the blade assembly of the Jar rotates freely.
Place the Jar over the Coupler on the Basic Unit. Turn
clockwise to lock.
Cover the Jar with the Lid after putting the ingredients.
Switch on the machine. To start with, press switch no. 1 and
IDENTIFY YOUR JUICER MIXER GRINDER GL 4015 / JUICER GL 4015 - JU
USING THE LIQUIDISER JAR / DRY GRINDER / CHUTNEY JAR
Juicer Spout Cover
Pusher
Juicer Mesh
Spatula
Liquidiser Jar
With J.M.G. 4015
With J.M.G. 4015
With J.M.G. 4015
With J.M.G. 4015
With J.M.G. 4015
Grinder Jar
Chutney Jar
Fruit Filter
then for higher Speeds move on to speed No. 2 and 3. (for additional
froth for Lassi, Cold Coffee use the Pulse switch).
To remove the Jar, switch off the machine & turn the Jar gently in anti-
clockwise direction.
The Glen fruit filter is used for juicing soft seeded fruits like water melon, grapes etc. It can also be used to make
tomato purees. Coconut milk coconut can also be extracted using the fruit filter. Blender jar without fruit filter is used
for blending / liquidising applications.
Cut small pieces of fruits (like watermelon, tomato etc.) to be juiced. Remove the cap on the lid by rotating
anticlockwise. Put the cut pieces into the filter and switch on the juicer mixer grinder. You can continue adding more
fruit pieces from the centre opening in the lid as they are juiced. The juice is sieved out through the filter and the
pulp/seeds get accumulated inside the filter.
Once the juicing is over, replace the cap. Remove the jar assembly from the drive shaft and pour out the contents
from the jar by tilting.
FRUIT FILTER
USING THE FRUIT FILTER
Insert the fruit filter into the blender jar and rotate it slightly so that it
settles down and the grooves get locked with the slugs on the blender jar
wall.
Place the lid on the jar (Drainage windows of lid towards jar spout) and
rotate it anti-clockwise to lock.
Place the assembly onto the drive shaft of the juicer mixer grinder and
rotate clockwise to lock it into position.
CLEANING THE LIQUIDISER JAR
After use unlock the Jar and pour out the contents & put it back over the
Coupler on the Basic Unit.
Fill of the Jar with warm water, add little liquid soap. Fix the Lid & run
the machine for about 30 seconds by pressing speed No. 1 Switch OFF
and unplug the machine.
Pour out the soap water & unscrew the Goblet by rotating anti-clockwise
and wash the Jar in running tap water.
Wipe the screw area with a wet cloth and then with dry cloth.
Wipe clean the rubber gasket and blade assembly and refit the Goblet Seat on the Liquidiser Jar. Ensure that the
rubber gasket is put on top/ bottom of the blade assembly before tightening the Jar with Goblet Seat.
Pour a little soap and water into the jar, close the lid and run it on position 1 for few seconds.
Pour out the soap solution and rinse with tap water.
Alternatively use a soft brush to clean the filter under running tap water.
CLEANING THE GRINDER JAR / CHUTNEY JAR / FRUIT FILTER
OVER LOAD PROTECTION
To protect the motor from burning, in case of overload, the appliance is fitted with an automatic
overload protector under the base of the basic unit. If the motor stops it is an indication of
excess load. Switch off the unit, take out excess material from the jars. Wait for 2/3 minutes
and press the overload protection plunger. Then restart the unit.
Note : Overload protection plunger is to be pressed to restart only after 2/3 minutes.
Plunger
STEPS TO SAFETY
While grinding always ensure that the blades are covered by the substance to be ground. Give a break of atleast one
minute after continuous Dry Grinding of 3 minutes.
Fill the blender Jar only upto ¼th of its capacity and add required amount of water or milk so that the blades don’t get
jammed.
Fill the Jar only ¾th of its capacity to avoid spilling of liquid, when you start the machine.
Do not allow children to handle the JMG / Juicer. Keep the machine away from direct heat and sunlight, at a suitable
height on a flat surface for easy operation.
Do not use the JMG for ice crushing or grinding raw Meat.
Before running the machine ensure that the mesh assembly, jars and lids are firmly placed and locked. Do not remove
or replace jars when the motor is on.
While operating run the machine in short cycles of 30-90 second as per requirement, do not run it for a long duration.
Clean the mesh with a soft nylon brush. Do not use any metallic object or knife etc.
Wide voltage fluctuations during operation may affect the quality of grinding, the motor may still be safe. It is safer to
use a JMG / Juicer only when you get Steadier voltage in your area.
While dry grinding the jar may get heated up due to friction. Don’t worry it has nothing to do with the motor.
Do not overload or run the Machine empty , In case of smoke or smell put off the machine & call Glen customer care.
