Wall Mounting
IMPORTANT - The wall brackets supplied with the heater must
be used.
Four identical wall mounting brackets are secured to the base of
the heater with a fixing screw. To wall mount appliance, first re-
move the brackets as follows :
Lay the heater on its back. Following the sequence in Fig. 3 –
identify and remove the fixing screw securing the brackets as
shown in (a), then pull out brackets to disengage them from the
slot (b), rotate them and withdraw the brackets from the slot (c)
.
The heater should be positioned observing the minimum
clearances - see
Fig.1
and in accordance with the safety warnings.
Select a suitable position on a wall, near to a mains power socket,
making sure that there is
at least
60 mm below the heater and
at
least
600 mm above the heater of unobstructed space. See also
‘Positioning the heater’.
Fix the two top retaining brackets to the wall, using suitable fixings
at 480 mm centres – see Fig 4.
Locate the heater on the top brackets and allow it to hang in
place.
Fit the bottom brackets into the slots in the heater and then fix it to
the wall.
Test that the heater is now securely fixed to the wall.
Using the heater
Plug in and switch on at the wall socket, the ‘mains on’ neon will
light when the heater is connected to the power supply.
The heat output is 500 watts.
PLEASE NOTE
–
THE ELEMENT HAS BEEN COATED WITH A
PROTECTIVE FILM WHICH WILL BURN OFF DURING THE FIRST
FEW MINUTES OF USE AND MAY CAUSE A SMALL AMOUNT OF
FUMING. THIS IS QUITE NORMAL – THE FUMES ARE NON-TOXIC
AND WILL QUICKLY DISAPPEAR. WE RECOMMEND THAT YOU
OPEN A WINDOW TO VENTILATE THE ROOM WHEN USING THE
HEATER FOR THE FIRST TIME.
Safety - overheat protection
The heater is fitted with a cutout which switches off the supply in
the event of overheating caused by covering the heater. Normal
operation will be automatically resumed shortly after removing
the covering article.
Cleaning and User Maintenance
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of
any kind on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust
and a damp cloth (not wet) to clean off stains. Be careful not to
allow moisture into the heater.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice in
your country.
After Sales Service
Your product is guaranteed
for one year f
rom the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge provided it has been installed and operated in
accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance with
this product please go to
www.dimplex.co.uk
where you will
find our self help guide by clicking on “After Sales” or ring our
helpdesk on 0845 600 5111 (UK) or 01 842 4833 (R.O.I.) .
Please retain your receipt as proof of purchase.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)
EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
GDC GROUP LTD
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex.
A division of GDC Group Ltd.
TEL: 0845 600 5111
FAX: 01489 773050
WEBSITE: www.dimplex.co.uk
Republic of Ireland
Tel.
01 8424833
480
(a)
(b)
(c)
Fig. 3
Fig. 4
