Dimensions
(millimetres)
Installation and Operating Instructions
Glen Skirting Heater
Model : 2150
INGSUK2150 Issue 7
Model
Specification
2150
0.5KW Neon
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
If the appliance is damaged, check immediately with the
supplier before installation and operation.
WARNING – THIS APPLIANCE MUST NOT BE USED IN A
BATHROOM.
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED
IMMEDIATELY BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET ARE FITTED
CORRECTLY OR IT HAS BEEN WALL MOUNTED.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at
the top of the heater or the air inlet slots in the base of the
heater.
WARNING: This heater is not equipped with a device to control
the room temperature. Do not use this heater in small rooms
when they are occupied by persons not capable of leaving the
room on their own, unless constant supervision is provided.
WARNING: In order to avoid overheating, do not cover the
heater.
Caution: In order to avoid a hazard due to inadvertent resetting
of the thermal cutout, this appliance must not be supplied
through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by
the utility.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the
appliance.
If young children, the aged or infirm are likely to be left in the
vicinity of the heater, we advise that adequate precautions
should be taken. We recommend that a guard be fitted to
ensure contact with the heater is avoided and objects cannot
be inserted into the product.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or a similarly qualified person
in order to avoid a hazard.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an ~ supply only and the voltage
marked on the heater must correspond to the supply voltage. This
heater is fitted with a rewireable plug incorporating a 13 amp fuse.
In the event of replacing the fuse in the plug supplied, a 13 amp
IMPORTANT : If the plug is not suitable for your socket, the 13 amp
plug should be removed. Before wiring the appropriate plug, please
note that the wires in this mains lead are coloured in accordance
with the following code :
GREEN AND YELLOW:
EARTH
BLUE :
NEUTRAL
BROWN :
LIVE
Connect the
GREEN AND YELLOW
wire to the terminal marked ‘
E
’
or by the earth symbol
, or coloured
GREEN
or
GREEN AND
YELLOW
.
Connect the
BROWN
wire to the terminal marked ‘
L
’ or coloured
RED
.
Connect the
BLUE
wire to the terminal marked ‘
N
’ or coloured
BLACK.
General
The heater may be used free standing on feet or wall mounted on
the brackets. The necessary feet and wall brackets are provided.
The heater should only be operated when in the upright position
as shown in
Fig.1
.
Fitting Feet
To attach the feet, use the
two screws provided in the base of the
heater.
Positioning the heater
When using the product free standing always ensure that the
heater is stood on a firm, level base near
to, but not directly
beneath, a suitable mains supply socket, ensuring at least 600mm
clearance from any shelf above.
Ensure that curtains and furniture are not positioned close to the
chosen position, as this would create a potential fire hazard.
See also ‘Important Safety Advice’.
NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET
FITTED.
Fig. 1
Lay the heater on its back, (If wall brackets attached, remove),
locate the foot fixing screw (see ‘a’ in
Fig. 3
). Remove the screw
using an X–head screwdriver, then align foot over hole in base
and insert the foot fixing screw, tighten using a screwdriver to
secure the foot.
Fig. 2
fuse approved by ASTA to BS 1362 must be used. If any other type
of plug is used, a 15 amp fuse must be fitted in the plug, the
adaptor, or at the distribution board.
230
209
815
120
600
175
60
