background image

Model # 7LIECH-BP-G: Page 11

IMPORTANT: Do NOT Return Dispenser To Store. 

If you have a question or problem, please contact 844-GLACIAL(452-2425) for assistance. 

 

 
 
 

                   Excessive Weight Hazard
Use two or more people to move and  install the 

water cooler and the bottles.
Failure to do so can result in back or other injury.

WARNING

Dispensing Cold Water

Note: After setup, it will take up to 6 hours to get the water to its maximum cold temperature. 
During this time, the compressor will run continuously. Compressor works to build up ice bank, 
this is normal. 

1.   Position the bottle, glass, pitcher, or cooking pot securely below the cold water tap.

   

 - The right triangle below the cold water control indicates the location of the cold water    

tap(See Parts & Features NO. 6).  

    - The circular shapes in the drip plate help align the flow of water. This unit dispenses water 

at a fast rate. To avoid splashes, hold the cup as close to the tap as possible. 

2.   Press the cold water control downward to start dispensing water. 

3.   Release the cold water control once the desired fill level is achieved

Dispensing Hot Water

1.   Hot water available 15~20 minutes after set up.
2.   Red arrow and target holes in the grill indicate positioning of you container for dispensing 

hot water.

3.   Hold your container close to dispensing nozzle to avoid splashes.
4.   To activate hot water dispensing nozzle push red lock inwards and hot button downwards. 
5.   To stop dispensing hot water release the button.

Replacing an Empty Bottle

Note: Replace the bottle as soon as you notice that it is empty.
1.   Lift the bottle straight up to disengage it from the bottle probe. 

2.   Remove the tamper seal from the top of bottle cap of the fresh bottle. Do NOT remove the 

plastic cap. 

3.   Lift the bottle and insert it onto the probe. Apply slight pressure until the plug inside the 

cap pushes in and the bottle is seated. Water will begin to flow into the reservoirs, causing 
air bubbles in the bottle

Содержание 7LIECH-BP-G


















Отзывы: