Gilbarco TRIND MULTI 1 C00012-001-NF-D Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 26

background image

Installation

Page 18

MDE-3801 TRIND™ Multi 1 Transmitter/Receiver in Dispenser Retrofit Kit • 10/99

Connecting Remaining Cables

1

From A side, pass J250 end of cable R20437-G01, J176 and JA ends of cable R20665-G1 and
J177 and PA ends of cable R20665-G2 through card cage to B side.

2

From B side, connect J176 on cable R20665-G1 to P176 on Power Supply PCB.
Note: Detailed information provided on “Cable Block Diagrams” on page 24.

3

Connect J177 on cable R20665-G2 to P177.

4

Connect JA on R20665-G1 to PA on R20724-G1 cable.

5

Connect PA on R20665-G2 cable to JA on R20724-G1 cable.

6

Connect J250 on ribbon cable R20437-G01 to P250 on Gateway board on top of card cage.

From A side of unit make the following connections:

1

On ribbon cable R20437-G01, connect J258A to P258 on A side CRIND Logic Board.
Note: A side of split cable R20437-G01 has red wire.

2

On ribbon cable R20437-G01, connect J258B to P258 on B side CRIND Logic Board.

Connect R20580-G2 power cable according to the following:

Note: Connections are unit specific. Use appropriate connectors to intercept power by

installing R20590-G1 inline.

For units with:

Do the following:

System cable W02468

Install inline using 15 pin P601 and J601 connectors

System cable T19612

Install inline using 3 pin connectors J601/J708 and P601/P708

P186

P176

P177

JA and PA connectors on R20724-G1

pass cables
through cage

P250 on
Gateway Board

«
...
16
17
18
19
20
...
»

Содержание TRIND MULTI 1 C00012-001-NF-D



























Отзывы:

Нет отзывов

Похожие инструкции для TRIND MULTI 1 C00012-001-NF-D

Бренд: Icom Страницы: 108

Бренд: B&K Страницы: 12

Бренд: Neo Car Audio Страницы: 16

Бренд: Ebyte Страницы: 15

Бренд: Harman Kardon Страницы: 65

Бренд: Harman Kardon Страницы: 127

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 155

Stratophonic SR300B

Бренд: Harman Kardon Страницы: 10

BRUKSANVISNING AVR 255

Бренд: Harman Kardon Страницы: 58

Бренд: Harman Kardon Страницы: 60

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: Harman Kardon Страницы: 34

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 4

Бренд: Harman Kardon Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды