manualshive.com logo in svg

Gigabyte R262-ZA0, Руководство пользователя

Поделиться
Скачать
Gigabyte R262-ZA0 Скачать руководство пользователя страница 41

- 41 -

System Hardware Installation

3-8  Removing and Installing the Hard Disk Drive

Follow these instructions to install a 2.5" hard disk drive: 

1.  Press the release button.

2.  Extend the locking lever.
3.  Pull the locking lever in the direction indicated to remove the HDD tray. 

4.  Align the hard disk drive with the positioning stud on the HDD tray.

5.  Slide the hard disk drive into the HDD tray.

6.  Reinsert the HDD tray into the slot and close the locking lever. 

1

2

3

1

2

3

Read the following guidelines before you begin to install the hard disk drive:

• Take note of the HDD tray orientation before sliding it out.
• The tray will not fit back into the bay if it is inserted incorrectly.
• Make sure that the hard disk drive is connected to the connector on the backplane.

Содержание R262-ZA0













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды