Gigabyte H470 AORUS PRO AX, Руководство пользователя, Страница: 17 / 52

8) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel
®
Chipset supports RAID 0,
RAID 1, RAID 5, and RAID 10. Refer to Chapter 3, "Configuring a RAID Set," for instructions on configuring
a RAID array.
Pin No. Definition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Settings\IO Ports\
SATA And RST Configuration," for more information.
1
1
SATA3 5 3 1
4 2 0
7
7
DEBUG
PORT
G.QBOFM
DEBUG
PORT
G.QBOFM
DEBUG
PORT
G.QBOFM
9) M2A_SB/M2M_SB (M.2 Socket 3 Connectors)
The M.2 connectors support M.2 SATA SSDs or M.2 PCIe SSDs and support RAID configuration. Please
note that an M.2 PCIe SSD cannot be used to create a RAID set either with an M.2 SATA SSD or a SATA
hard drive. To create a RAID array with an M.2 PCIe SSD, you must set up the configuration in UEFI BIOS
mode. Refer to Chapter 3, "Configuring a RAID Set," for instructions on configuring a RAID array.
F_USB30
F_ U
B_
F_ F_
_
B
B S_
B
S B_
B
_ S
S_
_
B
_ U
_
B
S
12
3
12 3
12
3
1 2 3
1
1
1
1
B S S
S
_S
S S U
1 2 3
S 3
B S S S
U
_ _ 3
F_USB3 F
S _
S _
S _
S F
B_
B_
F
_ 0
S
S
_ 0 F
_ F
_
_
_ _B
U
S _S
_ S F_
B
USB 0_ B
B_
B_
F_USB3 F_USB30 3
_
_3 U
S _
80 110 60
M2A_SB
F_USB30
F_ U
B_
F_ F_
_
B
B S_
B
S B_
B
_ S
S_
_
B
_ U
_
B
S
12
3
12 3
12
3
1 2 3
1
1
1
1
B S S
S
_S
S S U
1 2 3
S 3
B S S S
U
_ _ 3
F_USB3 F
S _
S _
S _
S F
B_
B_
F
_ 0
S
S
_ 0 F
_ F
_
_
_ _B
U
S _S
_ S F_
B
USB 0_ B
B_
B_
F_USB3 F_USB30 3
_
_3 U
S _
80 60
M2M_SB
42
42
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Locate the M.2 connector where you will install the M.2 SSD, use a screwdriver to unfasten the screw on
the heatsink and then remove the heatsink.
Step 2:
Locate the proper mounting hole based on the length of your M.2 SSD drive. If needed, move the standoff
to the desired mounting hole. Insert the M.2 SSD into the M.2 connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it with the screw. Replace the heatsink and secure it to the original
hole. Make sure to remove the protective film from the bottom of the heatsink before replacing the heatsink.
110
- 17 -