Gigabyte GA-P67A-UD5-B3 Скачать руководство пользователя страница 51

Страница: 51 / 116

- 51 -

BIOS Setup

Onboard LAN Boot ROM

Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.

(Default: Disabled)

Onboard USB3.0 Controller (Renesas D720200 USB 3.0 Controller)

Enables or disables the Renesas D720200 USB 3.0 controller. (Default: Enabled)

USB3.0 Turbo (Renesas D720200 USB 3.0 Controller)

Enables or disables the Turbo USB mode for the Renesas D720200 USB 3.0 controller. The actual per-

formance may vary depending on the number of devices being installed. (Default: Disabled)

eSATA3 Controller (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back Panel)

Enables or disables the SATA controller integrated in the Marvell 88SE9128 chip. (Default: Enabled)

eSATA3 Ctrl Mode (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back Panel)

Allows you to decide whether to configure the SATA controller integrated in the Marvell 88SE9128 chip

to AHCI mode.

IDE

Configures the SATA controller to IDE mode. (Default)

AHCI

Configures the SATA controller to AHCI mode. Advanced Host Controller Interface

(AHCI) is an interface specification that allows the storage driver to enable advanced

Serial ATA features such as Native Command Queuing and hot plug.

SATA3 Firmware Selection

Determines whether to automatically update the firmware of the Marvell 88SE9128 chip.

Onchip

Keeps the original firmware version.

Auto

Lets the BIOS automatically update the firmware to the latest version. (Default)

eSATA3 RAID Configuration (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back

Panel)

Allows you to configure RAID for the Marvell 88SE9128 SATA controller. Refer to Chapter 5, "Configur

ing SATA Hard Drive(s)," for instructions on configuring a RAID array.

When a Cable Problem Occurs...

If a cable problem occurs on a specified pair of wires, the

Status

field will show

Short

and then length

shown will be the approximate distance to the fault or short.

Example:

Part1-2 Status = Short / Length = 2m

Explanation: A fault or short might occur at about 2m on Part 1-2.

Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their

Status

fields will show

Open

, and the length shown is the approximate length of the attached LAN cable.

Содержание GA-P67A-UD5-B3





















































































































Результаты поиска

Содержание GA-P67A-UD5-B3

Отзывы:

Бренды по названию

Популярные бренды

Gigabyte GA-P67A-UD5-B3, Руководство пользователя

Результаты поиска

Содержание GA-P67A-UD5-B3

Отзывы:

Бренды по названию

Популярные бренды