Gigabyte GA-8I865GMFK-775 Скачать руководство пользователя страница 22

Страница: 22 / 72

GA-8I865GM(F)K-775 Motherboard

- 22 -

English

8) BAT(Battery)

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's
instructions.

9) F_PANEL (Front Panel Jumper)

Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis
front panel to the F_PANEL connector according to the pin assignment below.

If you want to erase CMOS...
1.Turn OFF the computer and unplug the power cord.
2. Take out the battery gently and put it aside for about 10

minutes (Or you can use a metal object to connect the
positive and negative pins in the battery holder to make
them short for one minute).

3.Re-install the battery.
4.Plug the power cord and turn ON the computer.

HD-

HD+

RES+

RES-

Reset Switch

SPEAK-

MSG-

MSG+

PW-

PW+

SPEAK+

Speaker

Connector

Power

Switch

Message LED/

Power/

Sleep LED

IDE Hard

Disk Active LED

HD (IDE Hard Disk Active LED)

Pin 1: LED anode(+)

Pin 2: LED cathode(-)

SPEAK (Speaker Connector)

Pin 1: Power
Pin 2- Pin 3: NC
Pin 4: Data(-)

RES (Reset Switch)

Open: Normal
Close: Reset Hardware System

PW (Power Switch)

Open: Normal
Close: Power On/Off

MSG(Message LED/Power/Sleep LED)

Pin 1: LED anode(+)

Pin 2: LED cathode(-)

Содержание GA-8I865GMFK-775









































































Результаты поиска

Содержание GA-8I865GMFK-775

Отзывы:

Похожие инструкции для GA-8I865GMFK-775

Бренды по названию

Популярные бренды

Gigabyte GA-8I865GMFK-775, Руководство пользователя

Результаты поиска

Содержание GA-8I865GMFK-775

Отзывы:

Похожие инструкции для GA-8I865GMFK-775

Бренды по названию

Популярные бренды