GIGA-BYTE TECHNOLOGY R181-T90 Скачать руководство пользователя страница 64

Страница: 64 / 68

BIOS Setup

- 64 -

5-7 Server Management Menu

(Note) Advanced items prompt when this item is set to

Enabled

Parameter

Description

BMC Self Test
Status

Displays BMC Self Test status information.

BMC Device ID

Displays BMC device ID information.

BMC Device
Revision

Displays BMC device revision information.

BMC Firmware
Revision

Displays BMC firmware revision information.

IPMI Version

Displays IPMI version information.

BMC Interface (s)

Displays BMC interface information.

System Event Log

Press [Enter] to configure advanced items.

BMC Self Test Log

Press [Enter] to configure advanced items.

View FRU
Information

Press [Enter] to view the advanced items.

BMC network

configuration

Press [Enter] to configure advanced items.

Содержание R181-T90





































































Результаты поиска

Содержание R181-T90

Отзывы:

Похожие инструкции для R181-T90

Бренды по названию

Популярные бренды

GIGA-BYTE TECHNOLOGY R181-T90, Руководство пользователя

Результаты поиска

Содержание R181-T90

Отзывы:

Похожие инструкции для R181-T90

Бренды по названию

Популярные бренды