background image

9

Repair Instructions P420 / P420-0011 / P420-0021 / P422 / P423 and P425 

 

Note: Always take time to lubricate all metal and nonmetal parts with a light film of oil before reassembly.  This step 

will ensure proper fit, at the same time protecting the pump nonmetal parts (i.e., the elastomers) from cutting and 

scoring.

1)  With a socket wrench, 

remove the three dis-

charge valve plugs and 

three inlet valve plugs 

(32).  Inspect the o-ring 

(33) for wear and replace 

if damaged.

2)  Using  needle  nose  pli-

ers, remove the inlet and 

discharge  valve  assem-

blies  (27A).      Note:  It 

may become neccesary 

to remove the valve seat 

(27) from the valve casing 

using a slidehammer.

 

3)  By inserting a small screw 

driver  between  the  valve 

seat  (27)  and  the  valve 

spring  retainer  (30),  the 

valve  assembly  can  be 

separated.  

4)  Remove the o-ring (31).  

 

Inspect all parts for wear and 

replace as necessary. Apply 

one drop of loctite 243 to the 

valve plugs (32) and tighten 

to 107 ft.-lbs. (145 NM).

5)  Use a 8mm allen wrench 

to  remove  the  8  socket 

head  cap  screws  (34). 

Carefully  slide  the  valve 

casing  (26)  out  over  the 

plungers. 

6)  Remove seal case (20) 

and weep return rings 

(25) from the valve 

casing.

7)  Remove the pressure 

rings (24) and v-sleeves 

(23 - Note: P422 & P423 

pumps have a spacer 

ring) from the valve cas-

ing (26).  

8)  Remove the weep grooved 

seal (23 or 23B) together 

with pressure ring (24) 

P420 and P425 only) out 

 

of the seal case (20). 

Check O-rings (21).

IMPORTANT!

 The grooved 

seal (23) on the high-

pressure side is to be fitted 

carefully into the valve cas-

ing (26) using a screwdriver. 

Under no circumstances 

must the seal surface in the 

valve casing or the seal lip 

be damaged.

Содержание P400 Series













Отзывы: