Ghost Controls TSS1 Скачать руководство пользователя страница 26

Страница: 26 / 64

2 0 2 0

DIP SWITCH OPTION SETTINGS.

There are four DIP Switches located on the main control board (shown) that must be

positioned properly for your particular installation

A. DIP #1 OPEN DIRECTION.

The opening direction of the gate operator is determined by DIP#1.

DIP Switch # OFF Position

ON Position

Pull-To-Open (Factory Default):

Gate

is pulled to open into your property.

Push-To-Open Installation: Gate is pushed to open away from

your property.

B. DIP #2 ALARM WARNING.

The warning alarm is determined by DIP#2.

DIP Switch # OFF Position

ON Position

Warning Disabled: AUTOCLOSE and

initial gate movement alarm warning is

disabled. This does not disable the alarm

warning for consecutive obstruction as

required by UL325 safety standard.

Warning Enabled (Factory Default):

AUTOCLOSE and

initial gate movement warning is enabled.

C. DIP #3 MONITORED SAFETY DEVICES. Keep Switch To The Left (Factory Setting)

Unless Using

Monitored External Safety Devices Than Switch To The Right.

YOUR SYSTEM WILL NOT WORK IF SAFTEY MODE IS ON

AND YOU DO NOT HAVE MONITORED EXTERNAL

SAFETY DEVICES CONNECTED.

DIP Switch # OFF Position (FACTORY SETTING) ON Position

Patent-pending

SafeForce® Mode

(Factory Default):

Force output is

limited to ensure safe operation as

specified by Type C in UL325

requirement.

Monitored Safety Mode: Monitored safety devices required /

Compatible GHOST CONTROLS

safety devices only.

Monitored safety devices must be present and operate prop-

erly as specified by Type B1 or B2 in UL325 requirement. See

monitored safety device connection in the monitored photo

eye instructions manual for more details.

D. DIP #4 DOES NOT APPLY TO SINGLE GATES FOR DUAL GATE OPENING SEQUENCE.

Keep switch to the left.

Содержание TSS1

































































Результаты поиска

Содержание TSS1

Отзывы:

Бренды по названию

Популярные бренды

Ghost Controls TSS1, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TSS1

Отзывы:

Бренды по названию

Популярные бренды