GHM Delta OHM HVAC40 Series страница 22 Скачать руководство пользователя

Страница: 22 / 26

HVAC40…

- 22 -

V1.1

ORDERING CODES

HVAC40… Humidity and temperature transmitters / Hygrostats. Depending on the

model, RS485 Modbus-RTU output, 0...10 V voltage analog output, active

0...20 mA / 4...20 mA current analog output, 2-wire (current loop) 4...20

mA analog output or ON/OFF relay switch output. Measuring range:

0…100 %RH (recommended 5…80 %RH), -20…+80 °C. Power supply: 24

Vac/18...40 Vdc for HVAC4017… and HVAC40V17…models, 15...30 Vdc

for HVAC40A17… models, 12...30 Vdc for VAC40S17… models, 24

Vac/15...36 Vdc for HVAC40R17…models.

CCESSORIES

RS27

RS232 null-modem serial connection cable with SubD 9-pin connector

on the PC side and 3-pole connector on the side of the instrument.

CP27

Serial connection cable with USB connector on the PC side and 3-pole

connector on the side of the instrument. The cable has a built-in

USB/RS232 converter and it connects the instrument directly to the

USB port of the PC.

RS48

Cable for RS485 connection with built-in USB/RS485 converter. The ca-

ble has USB connector for PC and 3 separate wires for the instruments.

HD33

33%RH saturated solution for checking the relative humidity sensor,

complete with screw adaptor for probes

∅

14mm, M12×1 thread.

HD75

75%RH saturated solution for checking the relative humidity sensor,

complete with screw adaptor for probes

∅

14mm, M12×1 thread.

HD9008.31 Wall flange with cable gland to fix Ø 14 mm probes.
PG16

AISI304 cable gland for Ø 14 mm probes.

DELTA OHM metrology laboratories LAT N° 124 are ISO/IEC 17025 accredited by AC-

CREDIA for Temperature, Humidity, Pressure, Photometry / Radiometry, Acoustics and

Air Velocity. They can supply calibration certificates for the accredited quantities.

HVAC40 17

LCD:

Blank = Without LCD (not available for HVAC40R17…)

L = With LCD

Output:

Blank = 0…20 mA / 4…20 mA active current analog output

A = 2-wire (current loop) 4…20 mA output

V = 0…10 V voltage analog output

S = RS485 Modbus-RTU output

R = ON/OFF relay switch

Probe:

TC.2 = Probe with 2 m cable

TO = Horizontal probe

TV = Vertical probe

Содержание Delta OHM HVAC40 Series



























Результаты поиска

Содержание Delta OHM HVAC40 Series

Отзывы:

Похожие инструкции для Delta OHM HVAC40 Series

Бренды по названию

Популярные бренды

GHM Delta OHM HVAC40 Series, Руководство по эксплуатации

Результаты поиска

Содержание Delta OHM HVAC40 Series

Отзывы:

Похожие инструкции для Delta OHM HVAC40 Series

Бренды по названию

Популярные бренды