GHM 607132 Скачать руководство пользователя страница 23

Страница: 23 / 34

E44.X.01.6C-04

Mounting- and Operating Manual GIR 300

page 23 of 34

6.8 Interface mode

When the device is in the interface mode it won’t make any measurements by itself.
The value shown in the device’s display is sent via serial interface.
But the switching and alarm functions of the displayed value are still available.

The EASYBus-Address of the device needed for the communication can be set manually with the device
itself or with the help of an EASYBus-software (like EASYBus-Configurator).
Please note, when carrying out an EASYBus-system-

initialisation the device’s address will be reset auto-

matically.

This chapter describes how to configure the device as an EASYBus-display.
This instruction demands that you selected “

SEri

“ as your desired input type like it is explained in chapter

6.2.
The device has to display “

InP

“.

When pressing button 1 again, the device will display “

Adr

“ (address).

- Use button 2 and button 3 to select the desired address [0 ... 239] of the device.

Press button 1 to validate the selected device address. The display shows “

Adr

“ again.

You don’t need any further configuration but the outputs.

When pressing button 1 again, the device will be displaying “

outP

“ (output).

For configuring the outputs please follow the instructions given in chapter 6.9.

6.9 Selection of the output function

- After configuration of the input (chapter 6.3

– 6.8) you have to select the output function.

The display shows “

outP

“ (output).

Use button 2 and button 3 (middle or right button) to select the desired output-function

Description

Function

To select as

output

For switching

point setting

please

refer to chapter

Output 1

Output 2

No output, device is
used as display unit

inactive

(contact is open)

inactive

(contact is open)

2-point-controller

switching function 1

(active = contact closed)

switching function 1

(active = contact is open)

7.1

3- point-controller

switching function 1

(active = contact closed)

switching function 2

(active = contact closed)

7.1

2- point-controller with
min-/max-alarm

switching function 1

(active = contact closed)

min-/max-alarm

(alarm = contact closed)

2P.AL

7.2

min-/max-alarm,
common

min-/max-alarm

(alarm = contact is open)

min-/max-alarm

(alarm = contact closed)

AL.F1

7.3

min-/max-alarm,
individual

max-alarm

(alarm = contact closed)

min-alarm

(alarm = contact closed)

AL.F2

7.3

= Please take notice, that output 2 is a breaking contact of the relay, which means, that the con-

tact will be closed if the device have no power supply!

Note: please take notice, that output 1 and 2 has different contact types.

Through this the device will have different contact states by max- and min-alarm in case of no power supply
is present!

(Max alarm = contact is open, min alarm = contact is closed)

Depending on your output function setting, it may be possible that one or more settings described below
won’t be available.

When pressing button 1 again, the device will display “

1.dEL

“ (delay of output 1).

ADR

OVTP

1.DEL

Содержание 607132



































Результаты поиска

Содержание 607132

Отзывы:

Бренды по названию

Популярные бренды

GHM 607132, Инструкция по монтажу и эксплуатации

Результаты поиска

Содержание 607132

Отзывы:

Бренды по названию

Популярные бренды