•
Hold down
/ TIME CHECK
for about two
seconds to repeat the previous message.
•
Press
/ TIME SET
to skip forward to the
next message.
To stop message playback at any time,
press
PLAY/STOP
.
4. After playing all messages, the system
beeps and saves the messages. The total
number of messages in two Mailboxes
appears on the display.
5. To replay all messages, press the
corresponding mailbox
PLAY/STOP
.
Deleting Messages
You can delete messages individually during
playback, or all at once after playback.
To delete an incoming message (after listening
to it), press
ERASE
once during playback, “E”
appears on the display.
To delete all messages in the corresponding
mailbox after playback, hold down
ERASE
for
about two seconds. “E” is flashing rapidly on
the display, press the corresponding mailbox
button. The system beeps and all messages in
the corresponding mailbox are deleted.
Note:
If you hold down
ERASE
before playing
back all messages, the system beeps. You
cannot delete the new messages until you play
them all back.
20
21
22
To Reset
If an AC power failure occurs, or the AC power
adaptor comes out of the wall, your unit will
shut down until the power is restored.
If your unit is not operating properly when the
power is restored, proceed with a unit reset.
1. Unplug the AC adaptor from the power
outlet and telephone line from the wall jack.
2. Replace the 9 volt alkaline battery with a
fresh one.
3. Plug the AC adaptor back into the power
outlet.
4. Plug the telephone line back into the wall
jack.
5. Record a new outgoing announcement or
you can use the pre-recorded
announcement.
6. Set the date and time.
While you are away from your home or office,
you can access your system by remote
operation. Use a touch-tone phone to enter your
remote operation security code.
Operating the System from a Remote
Location
To use your system from a remote telephone,
you must enter a 3-digit remote operation
security code. The security code label is located
on the bottom of the unit.
1. Dial your phone number.
2. After the system answers, wait for the
outgoing message and the beep tone. Enter
your remote operation security code. The
unit will emit two beeps to indicate the code
was entered correctly.
3. Enter a remote command. See “Remote
Commands”.
Notes:
•
If the memory is full, the system will answer
calls after 10 rings, then announce
“memory is full” and emit three short beeps.
You can then enter the 3-digit remote code
to control the unit.
•
If you do not have CPC service and you
hang up while the system is playing back
messages, the system might not recognize
that you hung up.
•
If someone calls while the system is playing
the messages (in remote operation), the
caller hears a busy signal.
Turning Your System On
If you forget to turn your system on, you can
phone in from a remote location and turn it on
automatically.
1. Call your telephone number.
2. The system answers after 10 rings. After
the beep, enter your 3-digit security code.
3. After the second beep, press
9#
then hang
up. Subsequent messages will be recorded.
Remote Commands
If the correct code was accessed, you hear two
beeps.
Option
Press
Play messages in mailbox 1
1 #
Play messages in mailbox 2
2 #
Delete all old messages
3 #
(all messages must be played back)
Record new outgoing message
7 #
(Press 7# again to stop recording outgoing
message)
Turn system off/on
9 #
Monitor the room
0 #
When you press
1#
to play messages in
mailbox 1, or
2#
to play messages in mailbox
2 (during playback), you can then press the
following keys to get these remote functions.
Option
Press
Erase current message
3 #
Repeat previous message
6 #
Skip to next message
7 #
Repeat current message
8 #
Stop message playback
# #
After all your messages have been played, you
hear two short beeps. You have 20 seconds to
access the menu again, otherwise, the unit
disconnects automatically.
Note:
When you are in remote playback, if there
are new messages in mailbox 1 or mailbox 2,
enter the instruction “1#” or “2#”, only new
messages will be played back to you; if there
are no new messages in mailbox 1 or mailbox
2, enter the instruction “1#” or “2#”, all
messages will be played back to you.
23
24
REMOTE OPERATION
