GF signet 2551 Скачать руководство пользователя страница 10

Страница: 10 / 20

Signet 2551 Display Magmeter

K-Factor

060.000

K-Factor:

See the charts on pages 12-13 for values in pulses per U.S. gallon or in pulses per liter.

To use other units, convert the published values as appropriate.

Pipe Size:

Select the pipe size that is nearest to the nominal pipe size.

Averaging:

Set the averaging period based on the installation and

ow conditions. Smaller values

allow the 2551 to respond to changes in

ow rate quickly, while larger values smooth the

uctuations

caused by installation and

ow conditions. See page 11 for details.

Flow Units:

Set the units for the application. Four characters are available. The

rst three characters can be set to any symbol or alpha

character, upper or lower case. The following special symbols are located between the upper case and lower case menus:

• (centered dot)

(micro)

_ (blank)

- (dash)

/ (slash)

3 (for cubic units)

The last character selects the timebase for the

ow rate measurement.

Select S/s (seconds) M/m (minutes), H/h (hours) or D/d (days)

Total Factor:

Set the factor by which the totalizer will count. This setting is made in the application

units (i.e., gallons, liters, etc.)

Totalizer Units:

Set the Totalizer Units. This setting serves as a label for the totalizer displays only.

It has no effect on the measurement. The special characters listed in the Total Factor settings are
available here also.

Low Flow Cutoff:

Set a

ow rate that the 2551 Magmeter will use as a minimum threshhold.

If the

ow rate falls below this value, the 2551 will respond as if the

ow were zero.

Sensitivity:

Set a percentage of maximum range by which the

ow must change to override the

averaging feature and "jump" quickly to the new

ow rate. See detailed explanation on page 11.

The Setup menu contains all of the parameters necessary for the 2551 Magmeter to begin
measuring

ow.

NOTE:

The Security Code must be entered before any changes can be made to the Setup menu.

See page 17 for details related to the Options menu..

The values shown for each menu item represent
the factory standard setting. All 2551 magmeters
are packaged with these settings.

Set 4 mA

: (2551-22 and -42 versions only) Set the

ow rate where the current output will be 4 mA.

Set 20 mA

: (2551-22 and -42 versions only) Set the

ow rate where the current output will be 20 mA.

The 4 to 20 mA output may be spanned to monitor forward and reverse

ow rates.

ENTER

Pipe Size

2” DN50 >

Sensitivity

100% >

Flow Units

GPM >

Set 4 mA

-100 GPM >

Set 20 mA

100.00 GPM >

Total Factor

1000.0 >

Totalizer Units

Gallons >

Low Flow Cutoff

0.5 GPM

Averaging

25 secs >

Use the keypad to navigate through each setting.

Enter Code

0000

Setup enu

Signet Magmeter

RELAY 1

RELAY 2

ENTER

Enter Menu

Setup >

Содержание signet 2551





















Результаты поиска

Содержание signet 2551

Отзывы:

Похожие инструкции для signet 2551

Бренды по названию

Популярные бренды

GF signet 2551, Руководство по эксплуатации

Результаты поиска

Содержание signet 2551

Отзывы:

Похожие инструкции для signet 2551

Бренды по названию

Популярные бренды