GEZE TSA 160 NT F, Схема подключения

Страница: 5 / 64

TSA 160 NT
5
Notes
1 Notes
1.1 Important safety instructions
To ensure personal safety, it is important to follow these safety instructions.
X
Keep these instructions.
à
Only specialists who are authorised by GEZE are permitted to carry out installation, commissioning and maintenance.
à If unauthorised changes made to the system, GEZE cannot be made liable in any way whatsoever for any
resulting damages.
à
GEZE does not accept any warranty for combinations with third-party products. In addition, only original GEZE
parts may be used for repair and maintenance work.
à
Connection to the mains voltage must be carried out by a qualified electrician. Perform the power connection
and equipment earth conductor test in accordance with VDE 0100 Part 610.
X
Use an on-site automatic cut-out as the line-side disconnecting device, the dimensioning of which is matched
to the type, cross-section, type of routing and ambient conditions of the on-site feeder. The automatic cut-out
must have at least 6 A and max. 16 A.
à
Attach safety stickers to glass door leaves, mat. no. 081476.
X
In accordance with Machinery Directive 2006/42/EC, a safety analysis is to be performed and the door system
marked in compliance with CE Marking Directive 93/68/EEC before the door system is commissioned.
à
Observe the latest versions of directives, standards and country-specific regulations, in particular:
à
ASR A1.7 “Directives for doors and gates”
à
EN 16005 “Power operated pedestrian doorsets – Safety in use – Requirements and test methods”
à
DIN 18650, Part 1 and Part 2 “Automatic door systems”
à
“Guidelines for hold-open systems”
à
DIN VDE 100-600 “Installation of low-voltage systems - Part 6 Tests”
à
DIN EN 60335-2-103 “Household and similar electrical appliances - Safety; Particular requirements for drives
for gates, doors and windows”
à Accident Prevention Regulations, in particular BGV A1 (VBG1) “General Regulations” and BGV A3 (VBG4)
“Electrical Installations and Resources”
Swing door drive as a hold-open device in accordance with DIN 18263-4
à
The hold-open function of the swing door drive must be cancelled in the event of a fire alarm, fault or manual
triggering, the lock latch release (electric strike according to fail-secure principle) must be disabled and all the
signal transmitters for opening the door leaves must be switched ineffective.
à The swing door drives may only be used on single-leaf and double-leaf doors if the door frame or, as the case
may be, the passive leaf of the double-leaf doors is equipped with an electric strike that releases the lock latch
and/or unlocks a safety catch with a spring-loaded latch.
1.2 Installation information
à
The drive is designed exclusively for use in dry rooms.
X
Use only the cables specified on the cable plan provided. Cables must be shielded in compliance with the wiring diagram.
X
Always use insulated wire-end ferrules for wire cores.
X
Insulate wires that are not used.
X
Secure loose, internal drive cables with cable ties.
X
Observe the maximum permitted overall current drain required to supply the periphery.
1.3 Safety-conscious working
X
Secure the workplace against unauthorised entry.
X
Watch the swivelling range of long system parts.
X
Secure the cover/drive/roller guide rail or link arm against falling.
X
Before carrying out work on the electrical system, cut the voltage supply (mains and rechargeable battery)
and check that no voltage is present. When an Uninterruptible Power Supply (UPS) is used, the system will still
be under voltage even when disconnected from the mains.
à
Risk of injury by moving parts (drawing in of hair, clothing, …) when a drive is opened.
à
Danger of injury caused by unsecured crushing, impact, drawing-in or shearing spots.
à
Danger of injury due to sharp edges in the drive.
à
Risk of injury due to glass breakage.
à Danger of injury through link arm or lever arm snapping back.
à Danger of injury when working at a great height.