GEZE Slimdrive SC Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

background image

Rod locking

7

Assembly of RC2 variants of the Slimdrive SL product family

5

Assembly of RC2 variants of the Slimdrive SL product family

The 1-leaf right hand slide to open variant is assembled as the mirror image to the 1-leaf left hand slide to open variant.

5.1 Pre-conditions

à

Drive is set up completely

à

Cover is removed

à

Locking device (2) is in the unlocked

position (dead bolt (1) is retracted into

the housing)

5.2 Fitting the door leaf

5.2.1 Fitting the door leaves

WARNING!

Risk of injury due to glass breakage.

X

Always mount the door leaf together with another person.

The base structures (11) are available as an option (support bracket, base plate).

See the installation diagrams for the RC2 variants of Slimdrive SL and Slimdrive SLT.

«
...
5
6
7
8
9
...
»

Содержание Slimdrive SC





















Отзывы:

Нет отзывов

Похожие инструкции для Slimdrive SC

Бренд: Mahe Страницы: 48

RazorCut 45 KUPJRRW45

Бренд: Unimig Страницы: 24

Бренд: Magneti Marelli Страницы: 44

Бренд: Aqua-Hot Страницы: 49

Бренд: OMEGA AIR Страницы: 9

Бренд: Lincoln Electric Страницы: 56

Бренд: Chicago Electric Страницы: 13

Бренд: Dormakaba Страницы: 10

Бренд: Dormakaba Страницы: 16

Бренд: Woodhaven Страницы: 2

Бренд: CornellCookson Страницы: 23

Бренд: Jasic Страницы: 44

HeatBloC MC 41 DN 25

Бренд: PAW Страницы: 32

Бренд: Neopost Страницы: 95

Бренд: Viesta Страницы: 22

Indoor Door Contact IDC200

Бренд: Videofied Страницы: 4

Бренд: Jade Safety & Security Страницы: 2

Бренд: Anvil Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды