GEZE FA GC 150 Скачать руководство пользователя страница 38

Страница: 38 / 60

GEZE hold-open system FA GC 150

Wiring diagram

5.5.1 Manual trigger switch UTA

Manual trigger switch UTA, AS500, ID 116266

Surface mounting cap, single, AS500, ID 120503

Note the requirements on the installation of manual trigger switch in chap. 3.5.

Installation in flush-mounted or cavity box

Install in such a way that removing the wireless module and manual trigger switch is only possible after these

two assemblies have been disconnected from one another (e.g. installation of the two assemblies in two dif-

ferent flush-mounted boxes).

2,2 k

GC 175

Fig. 5.5.1.1

Several manual trigger switches are connected in parallel. Only connect the 2.2 kΩ resistor in the last one.

UTA

2,2 k

GC 175

UTA

Fig. 5.5.1.2

The cable to the first manual trigger switch (UTA) must be laid separately or protected.

5.5.2 Contact to the fire alarm system

Line monitoring is active if:

a 2.2 kΩ resistor is connected in parallel at the contact of the fire alarm system.

Connect the potential-free contact as a normally open contact

GC 175

Potential-free contact (BMA)

Fig. 5.5.2.1

German

institute for

construction

technology

5.5.3 Contact of the fire alarm system and manual trigger switch UTA

The general construction technique permit requires line monitoring to the potential-free contact of the fire

alarm system and to the manual trigger switch.

Line monitoring is active if:

a 2.2 kΩ resistor is connected in parallel at the end of the cable.

Connect the potential-free contact as a normally open contact

Potentialfreier Kontakt (BMA)

2,2 k

GC 175

UTA

Fig. 5.5.3.1

The cable to the potential-free contact (fire-alarm system) must be laid separately or protected.

5.6 Alarm output

Potential-free relay output, changer, maximum 24 V, 1 A

In normal operation the contact 11-12 is open, in the event of power failure or alarm closed.

Do not supply alarm display from the hold-open system.

24 V external

Alarm

display

GND external

Fig. 5.6.1

5.7 Mutual triggering of two hold-open systems

Two hold-open systems can trigger each other mutually. For this purpose, the alarm contact of the one lintel-

mounted smoke switch is connected with the input MRB of the other lintel-mounted smoke switch.

If additional manual trigger switches are required, these are connected in parallel to the connection at the

respective input MRB.

Remove jumper J1 from both lintel-mounted smoke switches.

The general construction technique permit requires monitoring of the lines between the two lintel-mounted

smoke switches.

Line monitoring is active if:

jumper J3 of the two lintel-mounted smoke switches to the measuring chamber is set (2-3, see chap. 4.4),

a 43 kΩ resistor is connected in parallel at both lintel-mounted smoke switches directly at the alarm output.

German

institute for

construction

technology

Potential-free contact (BMA)

German

institute for

construction

technology

Содержание FA GC 150





























































Результаты поиска

Содержание FA GC 150

Отзывы:

Похожие инструкции для FA GC 150

Бренды по названию

Популярные бренды

GEZE FA GC 150, Инструкция по установке

Результаты поиска

Содержание FA GC 150

Отзывы:

Похожие инструкции для FA GC 150

Бренды по названию

Популярные бренды