Instructions for Use G-ST 6000+ G2
General Safety Instructions
Commissioning
The device may only be commissioned by qualified
personnel who are familiar with the device and the
technology.
Make sure that all applicable safety requirements are
fulfilled.
WARNING
Electrical voltages!
Personal and property damage
►
All connection work should only be performed
on the device when it is switched off.
►
Do not remove the housing cover.
Use only shielded cables for all control lines. Twist the
cable shield at the end and solder it to the frame of the
SUB-D connection (plug or socket). Keep the twisted part
of the cable shield in the plug (socket) as short as
possible.
WARNING
Electrical voltages!
Personal and property damage
►
Do not short-circuit the cable cores with the
cable shield.
►
Slide the insulating sleeve over the shield.
►
Do not place the cable shield on a ground
connection (pin).
Use a socket with a protective contact to connect the
power-supply unit.
Ensure a power supply of 110 VAC to 230 VAC. When
connecting external contacts, do not apply voltages above
3.3 V, this may cause damage.
The operating system is precisely preconfigured for your
device.
NOTICE
Impairment by pressing a key!
Impairment of the configuration
►
Avoid pressing a key while the device is
powering up.
Operation
When operating the device, the local applicable laws,
other regulations, standards, and rules of technology
must be observed. In the interest of a safe work process,
operating company and supervisors are responsible for
their compliance.
During all work, check the device for any damage. All
parts must be correctly mounted and fulfill all conditions to
ensure proper operation.
WARNING
Electrical voltages!
Personal and property damage
►
Do not use the device if it is damaged.
►
Disconnect the device from the power supply.
Do not use the supply cable for purposes for which it is
not intended. Protect the cable from heat, oil, and sharp
edges.
In dangerous situations or in case of malfunctions,
disconnect the device from the power supply immediately.
Repair and Maintenance
Ensure that the device is repaired professionally. Mark
the defect clearly and disconnect the power plug so that
no accidents or damage can occur due to a defective
device or be caused by it until the device is repaired.
Do not remove the housing cover! There are only
maintenance-free components inside the device.
WARNING
Electrical voltages!
Personal and property damage
►
Disconnect the device from the power supply
during all repair and maintenance work.
►
Work on the electrical equipment may only be
performed by a qualified electrician.
CAUTION
Danger due to the use of non-original parts!
Personal and property damage
►
Only use original spare parts.
WARNING
Explosion hazard!
If the mainboard battery is replaced by an unsuitable
battery type, explosions may occur.
►
Make sure that a suitable battery type is used.
►
Dispose the battery according to the valid legal
requirements and local regulations.
Front View (Without Cover)
No. Element
1
Operation indicator LED
Power
(white).
2
Error indicator LED
Error
(red).
3
Recording LED
Record
HDD
(white).
4
USB ports.
5
Trigger key
Action
(can be operated with a finger).
6 Reset
key (can be operated with 2 mm stylus).
7 Power
key (can be operated with 2 mm stylus).
8 Alarm
Reset
key (can be operated with 2 mm stylus).
9
LED (yellow): HDD in use.
10
LED (red): Power-supply unit error.
11
LED (white): Fan error.
12
2x SSD (exchangeable).
13
8x S-ATA hard disk drive (exchangeable).
Rear View
No. Element
1
Connections for power supply.
2
Control inputs for connecting external contacts for event-controlled image recording / relay outputs.
3
Port for PS/2 keyboard (6-pin mini-DIN socket).
4
Port for PS/2 mouse (6-pin mini-DIN socket).
5
USB 2.0 ports.
6
Display Port outputs for connecting a PC monitor.
7
DVI-D graphics output for connecting a PC monitor.
8
Serial RS-232 interface COM1 (9-pin Sub-D connector).
9
2x USB 3.1 (Gen1), 2x USB 3.1 (Gen2).
10
Network port (Ethernet 10 /100 / 1000 Base/T - RJ45).
11
Sound card ports.
12
10/100 Mbps port for remote control of RAID controller.
13
AnalogKit Audio Line In (3.5 mm stereo jack) optional.
14
AnalogKit FBAS inputs optional.
