Notice for Operation
P.9
Lid, Measuring Cup, Seal Ring
P.8
•
Insert the measuring cup into the lid (align the two taps to grooves of the lid and turn counter-clockwise).
Then put the lid on the blender jar by simply pushing down. To open, simply pull up the lid.
•
The seal ring is detachable. It can be removed from the lid and be washed separately, cleaning off any
residues stuck in between.
•
Make sure the appliance is unplugged from electricity supply.
•
Do not immerse the unit base or power cord into water or other liquids.
•
Clean surface of the blender jar with soft cloth or sponge. The measuring cup and seal ring can be
disassembled for cleaning.
•
The blender jar can be rinsed with water. It can also be cleaned by filling it with 2 cups of water, put on the
lid and then press the Pulse Key. Pour out the water and dry using a soft cloth.
•
After cleaning, put the blender jar on the side or upside down to dry. Do not immerse the whole jar in
water.
•
Clean the unit base with soft cloth. NEVER immerse it in water or other liquids.
•
Caution: If the blender jar is in an upside down position, do not leave it close to the sink or basin to avoid
water spraying onto the bottom part of the jar. This may cause rusting of the bearing and hence affecting
the performance of the blender.
A Friendly Reminder : To effectively remove dirt on the jar and blades and help them last longer, do the
following: add in water and lemon, close the lid and then press “Pulse ” button for 2 to 3
times. Replace liquid with clean water and repeat the above step.
3 Easy Steps to Wash the Blender Jar
Caution: Do not immerse the blender jar into water
1.
Add 1-2 slices of lemon into 750ml water. Select the “Vegetable” Programme (1min56sec).
2.
Pour out water. Repeat Step 1.
3.
Pour out water, and wipe it dry with a clean cloth. Put the jar sideways and leave it alone to dry naturally.
Cleaning & Storage
•
For safety reason, the appliance cannot be turned on until the blender jar is placed on the unit base.
•
If the motor is operating at a slow speed for a prolonged period, the food is too thick, or there is not enough
liquid, the motor can become overheated and the temperature monitoring system will be triggered to stop
operation. In this case, switch off and unplug the appliance, let the unit base cool off for 45 minutes, place
it at a location with good ventilation, or use a fan to lower its temperature. The system will reset and the
blender can be used again.
•
During operation, close the lid tightly to avoid contents from spraying, and potential hazards.
•
Keep hands and utensils out of the blender jar while the motor is running to prevent the possibility of
severe personal injuries and/or damages.
•
When making hot beverages such as soybean milk, and bisque etc, please check whether the lid is
secured tightly to prevent it from coming off. It is advisable to start operation at a low speed setting and
then increase the speed gradually, or use the Pulse mode.
•
Always put liquids and soft textured foods into the blender jar first before adding hard textured foods or ice
cubes.
•
When operation finishes, please wait until the blade assembly comes to a complete stop before taking off
the blender jar to avoid damage to the motor.
•
If there is a scorching smell coming from the blender, stop operation immediately. It may be caused by the
abrasion of an unlevelled cushion base or overheating due to too much content in the jar.
•
When making sauces (e.g. almond sauce, jam and sesame sauce) or stuffings and nuts, put in at least 2
cups and no more than 3 cups of ingredients. Keep blending time under 2 minutes to avoid overheating.
Too much ingredients may lead to overloading and overheating of the motor. In this case, wait till the motor
has cooled down before resuming operation.
•
When blending thick and sticky food using high speed, please start operation at low speed first. If blending
doesn’t begin, disconnect the power and stir the content using a rubber stirrer to get rid of the air bubbles
trapped in the food. Then close the lid and resume operation.
•
It is recommended not to use the appliance non-stop for 10 minutes.
