manualshive.com logo in svg

Gerber SABRE 408, Процедура замены

Поделиться
Скачать
Gerber SABRE 408 Скачать руководство пользователя страница 5

 

Page 5 of 9

 

 

7 

Using the beam as a carrier, carefully slide lead screw forward out of the table.   

              

 

Installing the Y-Axis lead screw 

  To install the Y-Axis lead screw 

 

1 

Orient the replacement lead screw and nut assembly so the machined flats in the lead screw are at the 
rear. If necessary, rotate the lead screw nut to position it approximately 16

″

 from the front of the lead 

screw. Carefully slide the lead screw through the tie beam/spindle and insert the rear of the lead 
screw into the rear clamp. Using the beam as a carrier, move the lead screw to the end of the table. 
Support the front of the lead screw and move the beam forward past the center of the table.  Slide the 
front lead screw support block/bushing assembly onto the lead screw. Leave it loose until the lead 
screw nut is secured. 

              

 

Note:  Be careful not to drag the lead screw threads through the beam/spindle assembly to prevent damage to the 
threads. 

Содержание SABRE 408










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды